Коды ошибок аналоговых Коды ошибок аналоговых копировальных аппаратов Canon копировальных аппаратов Canon
Если Ваш аналоговый копировальный аппарат Canon выдал на индикации некий код, то узнать причину возникновения ошибки Вы можете в этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарата; а о том, как устранить сам сбой, есть много материалов в разделах "Ремонт", "Ликбез", "FAQ"; также Вы можете воспользоваться поиском или указателем материалов сайта
Document feeder board problem or document feeder interface problem
E500
Sorter
E620
Editing problem
Canon 3030, 3050
Код ошибки
Описание
E000
Fuser temp low. Heat lamp, thermoswitch, thermistor, SSR
E001
Fuser temperature too high or shorted thermistor
E002
Fuser temperature too low
E003
Fuser temperature too low
E004
SSR, or lamp reg. board
E010
Drive problem
E022
DV unit switching problem
E030
Counter not working/open
E202
Scan problem. Scan sensor, scan motor
E204
Scan problem. Scan sensor, scan motor
E210
Lens problem. Lens sensor, lens motor
E220
Exposure lamp
E240
DC controller (main board)
E400
RDF circuit board
E401
RDF pickup motor drive
E402
RDF belt motor drive
E403
RDF feed drive problem
E404
RDF exit motor
E411
RDF sensor problem
E500
Sorter board problem
E510
Sorter feed motor
E512
Sorter delivery motor
E514
Sorter delivery motor
E520
Sort stack motor
E530
Vibrator motor
E531
Stapler motor
E535
Vibrator motor
E540
Shift problem
E541
Shift problem
E710
DC controller
E711
DC controller
E712
DC controller. Document feeder board or cable
E800
Auto shut off relay
Canon 3225
Код ошибки
Описание
E000
Fuser problem
E010
Drive
E030
Counter
E050
Duplex side to side problem
E051
Duplex side to side problem
E200
Scan problem
E202
Scan return problem
E204
Scan
E210
Lens problem
E220
Blank lamp open or lens home problem
E240
Bad DC controller
E400
Document feeder board problem or document feeder interface problem
E500
Sorter
E620
Editing problem
Canon 3325
Код ошибки
Описание
E000
Low fuser temperature. Heat lamp, thermoswitch, thermofuse, thermistor, SSR
E001
High fuser temperature. Thermistor, SSR, pinched wire
E002
Low fuser temperature. Same as E002
E003
Same as E000/E001
E010
Same as E002
E022
Motor drive problem
E030
Counter
E202
Scan motor, sensor
E204
Scan motor, sensor
E210
Lens motor, sensor
E220
Exposure lamp
E240
DC controller (main board)
E401
Pickup drive problem (might be Doc. Feeder)
E402
Document belt drive problem
E404
Exit motor (document feeder)
E411
Document sensor (document feeder)
E500
Sorter/machine communication problem
E510
Sorter drive problem
E530
Sorter home sensor
E531
Stapler unit swing sensor
E540
Sorter cam sensor
E541
Sorter cam sensor
E710
DC controller (main board)
E712
DC controller or document feeder board
Canon 3525, 3725
Код ошибки
Описание
E000
Fuser problem
E010
Main motor, motor board, clock pulse
E030
Counter
E050
Duplex side to side problem
E051
Crossway registration
E200
Scan problem
E202
Scan return problem
E202
Scan home sensor or home scan
E204
Document sensor, scan reverse sensor or scale
E210
Lens
E220
Blank lamp open or lens home problem
E240
DC controller
E400
Document feeder board problem or document feeder interface problem
E500
Sorter
E620
Editing problem
Canon 3825
Код ошибки
Описание
E000
Low fuser temperature. Heat lamp, thermoswitch, thermofuse, thermistor, SSR
E001
High fuser temperature. Thermistor, SSR, pinched wire
E002
Low fuser temperature. Same as E002
E003
Same as E000/E001
E010
Same as E002
E022
Motor drive problem
E030
Counter
E202
Scan motor, sensor
E204
Scan motor, sensor
E210
Lens motor, sensor
E220
Exposure lamp
E240
DC controller (main board)
E401
Pickup drive problem (might be Doc. Feeder)
E402
Document belt drive problem
E404
Exit motor (document feeder)
E411
Document sensor (document feeder)
E500
Sorter/machine communication problem
E510
Sorter drive problem
E530
Sorter home sensor
E531
Stapler unit swing sensor
E540
Sorter cam sensor
E541
Sorter cam sensor
E710
DC controller (main board)
E712
DC controller or document feeder board
Canon 4035
Код ошибки
Описание
E000
Low fuser temperature
E001
High fuser temperature
E010
Main motor clock pulse
E011
Bind or load on main motor
E020
No TF for 3 minutes
E030
Copy counter
E050
Duplex unit
E201
Scan motor
E203
Scan motor
E210
Lens home
E240
DC controller
E241
DC controller
E320
CCD
E400
DC controller, 24V
E500
DC controller, 24V
E510
Finisher feed motor
E520
Stacker motor
E530
Guide plate shift motor
E531
Stapler motor
E620
DC controller, edit board
Canon 4050, 4080
Код ошибки
Описание
E000
No fuser heat
E001
High fuser temperature or shorter thermistor
E002
Low temperature or bad thermistor
E003
Fuser problem
E004
Bad SSR (heat staying on)
E010
Drive
E020
Black toner motor
E030
Counter
E080
Interface problem with color unit
E081
Vertical drive motor
E082
Horizontal drive motor
E083
Color unit sensor on right
E084
Color unit sensor on left
E085
Color unit release sensor or release or solonoid
E086
Color unit claw release
E089
Laser problem
E100
Laser problem
E110
Laser motor
E140
Laser
E202
Scan
E203
Scan
E204
Scan
E210
Lens
E223
Color unit filter drive motor
E240
DC controller
E401
RDF pickup motor
E402
RDF belt motor
E403
RDF feed motor
E411
RDF document sensor
E500
Sorter-Copier communication error
E510
Sorter drive
E512
Sorter drive
E513
Sorter drive
E514
Sorter drive
E520
Top limit sensor or stack sensor
E530
Sorter home sensor
E531
Stapler home sensor
E535
Stapler swing sensor
E540
Stack shift sensor
E660
IC card
E710
DC controller
E711
DC controller
E714
DC controller
E800
Power off circuit
Canon 4540
Код ошибки
Описание
E00
Low fuser temperature
E001
High fuser temperature
E010
Main motor clock pulse
E011
Bind or load on main motor
E020
No TF for 3 minutes
E030
Copy counter
E050
Duplex unit
E201
Scan motor
E203
Scan motor
E210
Lens home
E240
DC controller
E241
DC controller
E320
CCD
E400
DC controller, 24V
E500
DC controller, 24V
E510
Finisher feed motor
E520
Stacker motor
E530
Guide plate shift motor
E531
Stapler motor
E620
DC controller, edit board
Canon 4835
Код ошибки
Описание
E000
Low fuser temperature
E001
High fuser temperature
E002
Low fuser temperature
E003
Low fuser temperature
E010
Drive
E030
Counter
E080
Color change board problems
E081
Color horizontal motor problem
E082
Color horizontal motor problem
E083
Color problem in vertical direction
E084
Color problem in vertical direction
E085
Color problem in vertical direction
E086
Color unit claw release problem
E089
Color change incomplete
E100
Laser problem
E110
Laser motor problem
E140
Laser unit
E203
Scan drive problem
E210
Lens not home or won't leave home
E240
DC controller
E401
Document feeder pick up motor
E402
Document feeder belt motor
E403
RADF feed motor
E404
Document feeder motor
E411
Document feeder sensor
E500
Sorter to DC control interface problem
E510
Stapler/sorter motor
E530
Stapler swing motor
E531
Stapler swing motor
E540
Sorter bin motor
E541
Sorter bin motor
E710
DC controller
E711
DC controller
E712
DC controller to document feeder interface problem
Canon 6012F
Код ошибки
Описание
C
No problem. Means that the machine is correcting the fuser film tracking
CC
Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier
E000
Low fuser temperature
E001
High fuser temperature
E002
High fuser temperature
E003
Erratic fuser temperature
E007
Fuser film off track and will not repair itself
E010
Main drive problem
E030
Counter problem
E064
Scan problem, or power supply
E202
Scan problem
E210
Lens drive problem or lens sensor
E220
Exposure lamp stays on or off
E240
DC controller (main board) or composite power supply
E261
Zero cross problem. Power frequency or composite power supply
E400
Communication problem between boards
E803
24 volt problem
EO
Fuser problem
H
Fuser overheat
Canon 6030
Код ошибки
Описание
E000
Fuser did not heat up
E001
Fuser temperature too high
E002
Fuser temperature not rising at correct pace
E003
Fuser temperature drops
E004
SSR shorted
E210
Lens home problem
E212
Lens home problem
E220
Exposure lamp problem
E224
Blank shutter home problem
E240
DC controller or composite power supply problem
E400
Data communication problem
E401
Pickup motor problem
E402
Belt motor problem
E403
Feeder motor
E404
Delivery motor
E411
Document detect sensor
E500
Communication problem with copier
E510
Feeder motor
E530
Home sensor
E531
Staple swing sensor problem
E540
Bin shift motor rotation problem
E541
Bin motor
E710
DC controller
E711
Document feeder IC failure
E716
Cassette feed IC failure
E800
Auto power-off circuit problem
E901
Cassette feed motor
E902
Paper guide home sensor problem
Canon 6035
Код ошибки
Описание
E000
Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR, etc
E001
Fuser temperature too high. Same possibilities as E000, as well as shorted wire
E002
Fuser temperature not rising at correct pace. Same possibilities as E000
E003
Fuser temperature drops. Same as E003
E004
Fuser problem. AC driver, SSR bad, wire shorted
E010
Drive problem. Main motor, gears, etc
E030
Total counter
E064
Composite power board or DC controller
E065
Composite power board or DC controller
E202
Scan motor or scan sensor problem. Panel locked with no Код ошибки. Scan motor problem
E203
Scan problem or scan sensor
E204
Scan problem or scan sensor
E210
Lens sensor or motor problem
E212
Lens sensor or motor problem
E220
Exposure lamp or exposure lamp regulator board
E224
Blanking shutter motor or sensor
E240
DC controller or composite power supply problem
E244
DC controller
E400
RDF to copier communication problem
E401
RDF Pickup motor or pick up sensor
E403
RDF feed motor or pulse sensor
E404
RDF delivery motion problem
E404
RDF delivery motor problem
E411
RDF tray sensor or registration sensor
E500
Sorter main board or communication with copier
E510
Sorter feed motor
E530
Sorter guide bar motor
E531
Sorter stapler motor
E540
Sorter bin shift motor
E541
Sorter bin motor
E550
Sorter power supply
E710
DC controller
E711
DC controller
E712
Document feeder IC failure
E716
DC controller. Sorter
E800
Auto power off function (DC controller)
E901
Pedistal motor
E902
Jogger side plate sensor or motor
Canon 6045
Код ошибки
Описание
E000
Fuser did not heat up. Lamp, thermal switch, thermistors, connections, AC driver, DC controller, SSR, etc
E001
Fuser temperature too high. Same possibilities as E000, as well as shorted wire
E002
Fuser temperature not rising at correct pace, same possibilities as E000
E003
Fuser temperature drops. Same as E000
E004
Fuser problem: AC driver, SSR bad, wire shorted
E005
Fuser cleaning web, or problem with sensor, lever or connector. Service mode 6 is the probably reset for this
E006
Fuser feed connector
E010
Drive problem. Main motor, gears, etc
E013
Waste toner drive problem, or waste toner sensor switch has been actuated too many times
E015
Pickup motor power supply. Could be bad motor or motor board, or DC controller
E020
Problem with developer unit, toner hopper, hopper motor, connection, sensor or DC controller
E030
Total counter
E031
Option counter or total counter
E050
Holding tray (duplex) home position sensor motor or board
E051
Holding tray (duplex) home sensor motor or board
E202
Panel locked up, but might be no Код ошибки, scan motor problem
E203
Scan problem or scan sensor
E204
Scan problem or scan sensor
E210
Lens sensor or motor problem
E212
Lens sensor or motor problem
E213
Scan lock sensor or lock solenoid
E220
Exposure lamp regulator board
E240
DC controller or composite power supply problem
E243
DC controller
E400
RDF to copier communication problem
E401
RDF pickup motor or pickup sensor
E402
RDF belt motor or pulse sensor
E403
RDF feed motor or pulse sensor
E411
RDF tray sensor or registration sensor
E500
Sorter main board or communication with copier
E510
Sorter feed motor
E522
Sorter push bar motor
E523
Sorter reference wall motor
E524
Sorter multi-guide motor
E525
Sorter bin paper sensor automatic adjustment problem
E526
Sorter bin paper sensor automatic adjustment problem
E530
Sorter guide bar motor
E531
Sorter stapler motor
E532
Stapler motor
E533
Stapler inside paper sensor
E540
Sorter bin shift motor
E550
Sorter power supply
E710
DC controller
E711
DC controller
E712
Document feeder IC failure
E713
DC controller, sorter
E800
Auto power off circuit problem. Main switch or DC controller
E802
Auto power off circuit problem. Main switch or DC controller
Canon 6085
Код ошибки
Описание
E000
After power-on, the upper fixing roller does not reach 100 C within 5 min
E001
The temperature of the upper fixing roller exceeds 230 C for 5 sec or more
E002
After the temperature of the upper fixing roller has exceeded 100 C, it does not reach 180 C within 5 min
E003
After the temperature of the upper fixing roller has reached 180 C, it drops to 100 C or less for 5 sec or more
E005
The length used of the cleaning belt inside the fixing assembly has exceeded a specific value
E012
After the drum motor drive signal has been generated, clock pulses are not generated within 2 sec
E013
After the waste toner feeding screw has become locked, the detecting switch (SW20) is pressed a multiple number of times within a specific period of time
E014
When the fixing motor (M17) is rotating, an error is detected for 2 sec or more
E015
After the pick up motor drive signal has been generated, clock pulses have not been generated within 2 sec
E019
As many as 50,000 have been made after detecting a waste toner full condition
E020
During copying, the toner supply signal is 0', indicating the absence of toner, for 3 min or more. During toner supply sequence at time of installation, the toner supply signal does not go '1' after 6 min or more
E030
After the total copy counter has turned OFF, an open circuit is detected for the total copy counter
E032
After the clock pulse signal reached the IPC communication format of the copier DC controller PCB, the Copy Data Controller-A1 does not detect the signal
E050
While the paper jogging guide motor (M11) drive signal is being generated, the paper guide home position signal (THP) is not generated for 2 sec or more. While the paper jogging guide motor (M11) is being generated, the paper jogging guide home position signal (THP) is generated for two sec or more
E202
The scanner home position signal (SCHP) is not generated within 10 sec after the power switch or the Copy Start Key is pressed
E203
While the scanner motor drive signal is being generated, clock pulses are not generated within 2 sec
E204
The scanner leading edge signal (SCDP1) is not generated within 0.8 sec after the scanner has started to move
E209
The scanner C.F.F. position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent
E210
The lens X home position signal (SCFFP) is not generated within 10 sec after the C.F.F. has been sent
E212
The lens Y home position signal (LYHP) is not generated within 9 sec after the power switch or the Copy Start Key is turned ON. The lens Y home position signal (LYHP) is generated for 2 sec or more
E213
In stream reading mode, the scanner original leading edge sensor 2 signal (SCDP2) is not generated for 5 pages continuously
E214
While the scanner cooling fan (FM1, FM10, FM11) is rotating, an error signal is generated for 2 sec or more
E270
In stream reading mode, the scanner leading edge signal(SCDP2) is not generated within a specific period of time after a command has been issued to lock the scanner
E710
At power-on the IPC (Q170) on the DC controller PCB cannot be initialized
E711
After power-on the IPC (Q170) on the DC controller PCB goes out of order
E712
The communication IC on the RDF controller PCB has gone out of order
E713
The communication IC on the sorter control PCB has gone out of order
E715
The communication IC on the C.F.F. controller PCB has gone out of order
E717
The communication IC on the Copy Data Controller-A1 PCB has gone out of order
E800
An open circuit is detected
E801
Current flows from the activation circuit in the absence of the scanning lamp ON signal
E802
The relay (RL3) in the power supply unit does not operate in spite of the auto power-off signal
An error is identified in the communication between the sorter and the copier
E510
The clock signal from the motor is absent for 250ms or more
E510
Sorter motor drive
E513
The clock signal from the motor is absent for 250 ms or more
E530
Sorter home sensor
E530
The home position sensor (P17) fails to go OFF when an equivalent of 2560 pulses of the motor drive command has been generated
E531
The stapler unit swing sensor (MS9) fails to go ON within 500 ms after the motor drive command has been generated. MS9 fails to go back OFF within 1000 ms after it has gone on
E531
Stapler swing sensor
E540
The lead cam home position sensor (P12) fails to go OFF within 2000 ms after the motor drive command has been generated. P12 fails to go back ON within 2000 ms after it has gone OFF
E540
Sorter lead cam home sensor
E541
Sorter lead cam home sensor
E710
DC controller board
E711
DC controller board
E712
Document feeder problem
Canon 7050
Код ошибки
Описание
E000
Heater (Reset by unplugging machine)
E001
Heater triac, DC controller, AC driver (reset by unplugging)
E005
Fuser cleaner belt at end. Replace
E010
Main motor, DC controller or DC driver board
E011
Any motor ( main, scan, cleaner belt, duplex, toner, lens) DC driver, DC controller, duplex driver board
E020
Toner out signal has been sent for at least 3 minutes
E050
Duplex
E203
Scan motor, DC driver, DC controller
E210
Lens home sensor not actuated or won't deactuate
E240
Controller board
E241
Controller board
E242
Controller board
E400
DC controller, Doc. Feeder board, 24V power supply
E500
DC controller, sorter board, 24V power supply
Canon 720, 740, 770, 790
Код ошибки
Описание
C
No problem. Means that the machine is correcting the fuser film tracking
CC
Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier
E000
Low fuser temperature
E001
High fuser temperature
E002
High fuser temperature
E003
Erratic fuser temperature
E007
Fuser film off track and will not repair itself
E010
Main drive problem
E030
Counter problem
E064
Scan problem, or power supply
E202
Scan problem
E210
Lens drive problem or lens sensor
E220
Exposure lamp stays on or off
E240
DC controller (main board) or composite power supply
E261
Zero cross problem. Power frequency or composite power supply
E400
Communication problem between boards
E803
24 volt problem
E0
Fuser problem
H
Fuser overheat
Canon 7550
Код ошибки
Описание
E000
Heater (Reset by unplugging machine)
E001
Heater triac, DC controller, AC driver (reset by unplugging)
E005
Fuser cleaner belt at end. Replace
E010
Main motor, DC controller or DC driver board
E011
Any motor ( main, scan, cleaner belt, duplex, toner, lens) DC driver, DC controller, duplex driver board
E020
Toner out signal has been sent for at least 3 minutes
E050
Duplex
E203
Scan motor, DC driver, DC controller
E210
Lens home sensor not actuated or won't deactuate
E240
Controller board
E241
Controller board
E242
Controller board
E400
DC controller, Doc. Feeder board, 24V power supply
E500
DC controller, sorter board, 24V power supply
Canon 8070, 8570
Код ошибки
Описание
E000
Fuser problem. Temperature too low. Heat lamp, thermal fuse or thermoswitch, thermistor, triac etc
E001
Fuser problem. Temperature too high. Probably triac
E005
Fuser web finished
E005
Fuser cleaner belt user up
E010
Drive
E010
Main drive problem
E011
Drive problem. Could be main motor, scan motor, cleaning web motor or duplex motor
E020
Toner empty sensor sees no toner added for 3 min probably toner feed problem
The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90 sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150C within 8 min after power on. The surface temperature of the fixing assembly upper roller fails to reach 180C within 5 min after it has reached 150C. The surface temperature of the fixing assembly upper roller falls below 50C in standby
E001
The surface temperature of the fixing assembly upper roller exceeds 250C
E005
The cleaning belt inside the fixing assembly has been taken up more than a specified length
E010
After generation of the main motor drive signal, two or more pulses are not received within 2 sec
E020
The accumulative time during which the toner supply signal (TSP) has been generated by the developing assembly reaches 3 min
E050
The holding tray home position signal (THP) is not generated within 4 sec while the holding tray motor drive signal (TMDP1,2) is being generated. The holding tray home position signal (THP) is generated 1 sec or more while the holding tray motor drive signal (TMDP1.2) is being generated
E13
The error detection circuit on the waste toner feed motor driver PCB has detected on overcurrent
E203
Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal is generated
E210
The lens home position signal (LHP) is not generated within 4.8 sec after the power switch or door switch has gone ON. The lens home position signal (LHP) is generate 2 sec or more
E240
An error has occurred in the microprocessor on the DC controller PCB
E243
An error has occurred in the communication between the microprocessor of the DC controller PCB and the microprocessor in the control panel
E710
An error has occurred in the communication between the DC controller PCB and the controller PCB of the option, and the DC controller has detected the error
Canon 9800
Код ошибки
Описание
E000
The surface temperature of the fixing assembly upper roller fails to rise by a specified value within 90 sec after power-on. The surface temperature of the fixing assembly upper roller fails to reach 150C within 8 min after power-on
E001
The surface temperature of the fixing assembly upper roller exceeds 250C
E005
The cleaning belt inside the fixing assembly has been taken up more than a specified length
E010
After generation of the main motor drive signal, two or more pulses are not received within 2 sec
E013
The error detection circuit on the waste toner feed motor driver PCB has detected an overcurrent
E020
The accumulative time during which the toner supply signal (TSP) has been generated by the developing assembly reaches 3 min*
E050
The holding tray home position signal (THP) is not generated within 4 sec while the holding tray motor drive signal (TMDP1, 2) is being generated. The holding tray home position signal (THP) is generated 1 sec or more while the holding tray motor drive signal (TMDP1, 2) is being generated
E203
Input of two or more clock pulses is not received within 2 sec from the scanner motor drive signal is generated
E210
The lens home position signal (LHP) is not generated within 4.8 sec after power switch or door switch has gone ON. The lens home position signal (LHP) is generate 2 sec or more
E240
An error has occurred in the microprocessor on the DC controller PCB
E243
An error has occurred in the microprocessor of the DC controller PCB and the microprocessor in the control panel
E710
An error has occurred in the communication between the DC controller PCB and the controller PCB of the option, and the DC controller has detected the error
E712
No communication is perceived from the RF controller PCB for 200 ms or more the communication is monitored at all times
Canon A-1
Код ошибки
Описание
E500
An error is identified in the communication between the sorter and copier
E510
The clock signal from the motor is absent for 250 ms or more
E513
The clock signal from the motor is absent for 250 ms or more
E530
The home position sensor (P17) fails to go OFF when an equivalent of 2560 pulses of the motor drive command has been generated
E531
The stapler unit swing sensor (MS9) fails to go ON within 500 ms after the motor drive command has been generated. MS9 fails to go back OFF within 1000 ms after it has gone ON
E540
The lead cam home position sensor (P12) fails to go OFF within 2000 ms after the motor drive command has been generated. P12 fails to go back ON within 2000 ms after it has gone OFF
Canon C-120
Код ошибки
Описание
C
No problem. Means that the machine is correcting the fuser film tracking
CC
Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier
E000
Low fuser temperature
E001
High fuser temperature
E002
High fuser temperature
E003
Erratic fuser temperature
E007
Fuser film off track and will not repair itself
E010
Main drive problem
E030
Counter problem
E064
Scan problem, or power supply
E202
Scan problem
E210
Lens drive problem or lens sensor
E220
Exposure lamp stays on or off
E240
DC controller (main board) or composite power supply
E261
Zero cross problem. Power frequency or composite power supply
E400
Communication problem between boards
E803
24 volt problem
E0
Fuser problem
H
Fuser overheat
Canon C-160
Код ошибки
Описание
E000
Fuser thermistor, heater, thermal fuse
E001
Fuser thermistor, or triac
E002
Fuser thermistor, thermal fuse or triac
E003
Fuser thermistor, heater, thermal fuse or triac
E004
Triac or fuser won't shut off
E007
Fuser film is off center or not driving properly
E010
Main motor drive problem
E030
Counter
E064
Composite power supply or main board
E202
Scan problem
E210
Lens drive problem
E220
Exposure lamp
E240
Main board or composite power supply
E261
Composite power supply or fluctuating power
E400
ADF communication problem to machine
E402
ADF belt motor drive
E404
ADF exit motor
E411
ADF document detect, or registration sensor or edge sensor
E500
Sorter communication problem
E510
Sorter drive problem
E530
Stapler guide bar motor
E531
Stapler swing motor
E540
Bin shift motor
E541
Bin motor drive problem
E710
Main board
E711
Main board
E712
Main board or communication problem with ADF
E717
Main board, asst. board
U0
Initializing. Sets all user modes to factory default settings
U1
Auto clear timer. Range 1-9. Each digit=1 minute
U2
Automatic power shut off timer
U3
Fine adjustment of zoom
U4
Auto cassette switching
U5
Sort or non-sort default
U6
Cleans document feeder pickup assembly
U7
CLEAR "replace drum"
U9
Auto exposure or manual exposure as default
Canon C-180
Код ошибки
Описание
E000
Fuser problem. Low temperature. Lamp, thermal switch, AC driver
E001
Fuser problem. High temperature. Triac, AC driver, pinched wire
Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407
E010
Main motor drive problem
E030
Counter
E041
Paper deck motor, clutch or sensor
E064
Composite power supply or main motor board
E202
Scan problem. Motor sensor
E210
Lens drive problem
E220
Exposure lamp
E240
Main board or composite power supply
E260
Main board, power supply cooling fan or composite power supply
E261
Composite power supply or fluctuating power
E400
ADF communication to machine
E401
ADF pickup motor or sensor
E402
ADF belt motor drive
E403
ADF feed motor or slip sensor
E404
ADF exit motor
E411
ADF document detect, or registration sensor or edge sensor
E500
Sorter communication problem
E510
Sorter drive problem
E530
Stapler guide bar motor
E531
Stapler swing motor
E540
Bin shift motor
E541
Bin motor drive problem
E710
Main board (DC controller.)
E711
Main board (DC controller.)
E712
Main board or communication problem with ADF, or ADF main board
E717
Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies. Reset with user
E802
Composite power supply or DC controller
E901
Cassette feed unit board or cassette feed motor
E902
Horizontal registration problem. I think this refers to the duplex section
J1
Feed jam
J10
Duplex exit jam
J11
Vertical jam
J12
Vertical jam
J13
Vertical jam
J14
Vertical jam
J15
Deck jam
J2
Feed jam
J3
Separation area jam
J4
Separation area jam
J5
Exit jam
J6
Exit jam
J7
Sorter jam
J8
Door open jam
J9
Cassette jam
JA
Cassette jam
Jb
Cassette jam
JC
Cassette jam
Jd
Duplex feed jam
JE
Duplex exit jam
JF
Duplex registration jam
Canon NP
Код ошибки
Описание
E000
Fuser thermistor, heater thermal fuse
E001
Fuser thermistor, or triac
E002
Fuser thermistor, thermal fuse or triac
E003
Fuser thermistor, heater, thermal fuse or triac
E004
Triac or fuser won't shut off
E007
Fuser film is off center or not driving properly. Might be able to reset in service mode 4-407
E010
Main motor drive problem
E030
Counter
E041
Paper deck motor, clutch or sensor
E064
Composite power supply or main motor board
E202
Scan problem. Motor sensor
E210
Lens drive problem
E220
Exposure lamp
E240
Main board or composite power supply
E260
Main board, power supply cooling fan or composite power supply
E261
Composite power supply or fluctuating power
E400
ADF communication to machine
E401
ADF pickup motor or sensor
E402
ADF belt motor drive
E403
ADF feed motor or slip sensor
E404
ADF exit motor
E411
ADF document detect, or registration sensor or edge sensor
E500
Sorter communication problem
E510
Sorter drive problem
E530
Stapler guide bar motor
E531
Stapler swing motor
E540
Bin shift motor
E541
Bin motor drive problem
E710
Main board (DC controller.)
E711
Main board (DC controller.)
E712
Main board or communication problem with ADF, or ADF main board
E717
Main board, assist board. "Replace drum": Drum waste toner is full, or drum has run 40,000 copies. Reset with user
E802
Composite power supply or DC controller
E901
Cassette feed unit board or cassette feed motor
E902
Horizontal registration problem. I think this refers to the duplex section
J1
Feed jam
J10
Duplex exit jam
J11
Vertical jam
J12
Vertical jam
J13
Vertical jam
J14
Vertical jam
J15
Deck jam
J2
Feed jam
J3
Separation area jam
J4
Separation area jam
J5
Exit jam
J6
Exit jam
J7
Sorter jam
J8
Door open jam
J9
Cassette jam
JA
Cassette jam
Jb
Cassette jam
JC
Cassette jam
Jd
Duplex feed jam
JE
Duplex exit jam
JF
Duplex registration jam
Canon PC
Код ошибки
Описание
C
No problem. Means that the machine is correcting the fuser film tracking
CC
Drum must be changed. Could be the drum serial number is identified by the logic as being non-compatible to that particular copier
E000
Low fuser temperature
E001
High fuser temperature
E002
High fuser temperature
E003
Erratic fuser temperature
E007
Fuser film off track and will not repair itself
E010
Main drive problem
E030
Counter problem
E064
Scan problem, or power supply
E202
Scan problem
E210
Lens drive problem or lens sensor
E220
Exposure lamp stays on or off
E240
DC controller (main board) or composite power supply
E261
Zero cross problem. Power frequency or composite power supply
E400
Communication problem between boards
E803
24 volt problem
EO
Fuser problem
H
Fuser overheat
E000
Fuser thermistor, heater, thermal fuse
E001
Fuser thermistor, or triac
E002
Fuser thermistor, thermal fuse or triac
E003
Fuser thermistor, heater, thermal fuse or triac
E004
Triac or fuser won't shut off
E007
Fuser film is off center or not driving properly
E010
Main motor drive problem
E030
Counter
E064
Composite power supply or main board
E202
Scan problem
E210
Lens drive problem
E220
Exposure lamp
E240
Main board or composite power supply
E261
Composite power supply or fluctuating power
E400
ADF communication problem to machine
E402
ADF belt motor drive
E404
ADF exit motor
E411
ADF document detect, or registration sensor or edge sensor
E500
Sorter communication problem
E510
Sorter drive problem
E530
Stapler guide bar motor
E531
Stapler swing motor
E540
Bin shift motor
E541
Bin motor drive problem
E710
Main board
E711
Main board
E712
Main board or communication problem with ADF
E717
Main board, asst. board
U0
Initializing. Sets all user modes to factory default settings
U1
Auto clear timer. Range 1-9. Each digit=1 minute
U2
Automatic power shut off timer
U3
Fine adjustment of zoom
U4
Auto cassette switching
U5
Sort or non-sort default
U6
Cleans document feeder pickup assembly
U7
CLEAR "replace drum"
U9
Auto exposure or manual exposure as default
EO
Heater problem
E1
The heater film has gone off center. Turn machine off & on, make sure it's level etc
E2
Scan problme
E6
Exposure lamp or exposure lamp sensor
E000
Fuser problem
E001
Fuser problem
E010
Drive
E210
Zoom/lens/motor problem
E00
Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20 seconds
E001
Shorted thermistor or high-temperature, Exit sensor
E010
Clock Pulse
E210
Zoom Lens Problem
Canon PC6
Код ошибки
Описание
E000
Fuser problem
E001
Fuser problem
E010
Drive
E210
Zoom/lens/motor problem
Canon PC7
Код ошибки
Описание
E00
Heater, thermoswitch, exit sensor (Reset by jumping CP102 pins 1 & 2, or leave machine off for 20 seconds
E001
Shorted thermistor or high-temperature, Exit sensor
E010
Clock Pulse
E210
Zoom Lens Problem
Canon NP7161
Код ошибки
Описание
E000
The thermistor (TH1, TH2) has poor contact or an open circuit
The fixing heater (H1) has an open circuit
The thermal switch (TSW1) has turned on
The triac is faulty
The DC controller PCB is faulty
E001
The thermistor (TH1, TH2) has a short circuit
The triac is faulty
The DC controller PCB is faulty
E002 E003
The thermistor (TH1, TH2) has poor contact or an open circuit
The fixing heater (H1) has an open circuit
The thermal switch (TSW1) has turned on
The triac is faulty
The DC controller PCB is faulty
E004
The triac has a short circuit
The DC controller PCB is faulty
E010
The main motor (M1) is faulty
The DC controller PCB is faulty
E013
The waste toner feedscrew is locked
The waste toner feedscrew lock sensor (PS8) is faulty
The DC controller PCB is faulty
E030
The total copy counter has an open circuit
The DC controller PCB is faulty
E031
The accessories counter has an open circuit
The DC controller PCB is faulty
(E202)
No code indication. Keys are disabled
The scanner home position sensor (PS1) is faulty
The scanner motor (M2) is faulty
The DC controller PCB is faulty
E208
The mirror home position sensor (PS3) is faulty
The mirror motor (M4) is faulty
The DC controller PCB is faulty
E210
The lens home position sensor (PS2) is faulty
The lens motor (M3) is faulty
The DC controller PCB is faulty
E220
The lamp regulator PCB is faulty
The DC controller PCB is faulty
E261
The power supply frequency is faulty
The power supply PCB is faulty
E710 E711
The DC controller PCB is faulty
E712
The DC controller PCB is faulty
The ADF controller PCB is fault
The ADF cable is faulty
E717
The DC controller PCB is faulty
The Remote Diagnostic Device II PCB is faulty
E800
The auto power-off circuit has an open circuit
The DC controller PCB is faulty
E805
The exhaust fan (FM2, FM4) is faulty
The DC controller PCB is faulty
E821
The ozone filter is clogged
The cleaner thermistor (TH3) has poor contact or an open circuit
The DC controller PCB is faulty
Если Вы не смогли найти своей модели в этом разделе, то есть вероятность, что Ваш аппарат является аналогом одного из представленных здесь. Проверить это можно в разделе "Совместимость".
Коды ошибок аналоговых копиров Canon