Коды ошибок Коды ошибок копировальных аппаратов Konica копировальных аппаратов Konica
Если Ваш копировальный аппарат Konica выдал на индикации некий код, то узнать причину возникновения ошибки Вы можете в этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарата; а о том, как устранить сам сбой, есть много материалов в разделах "Ремонт", "Ликбез", "FAQ"; также Вы можете воспользоваться поиском или указателем материалов сайта
Konica 1015
Код ошибки
Описание
F09
Power leakage of some kind. Heat, exposure, AC or power supply.
F23
Toner motor
F26
Toner density adjustment problem. This means machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel that you should disconnect the toner motor first. This Код ошибки happens probably because either machine wasn't set up properly, or the customer kept on using the machine with the toner light on.
F28
Corona problem. Could be any corona. Must reset with "25: mode, "P45" set to "0"
F34
High fuser temperature
F35, F36
Low fuser temperature
F41
Scan home
F42
Scan home
F43
Exposure lamp
F45
Lens problem
F54
Fan motor
F60
ADF to main board communication problem
F67
ADF error
F77
Sorter gate
F88
AE adjustment problem
J11-J13
Feed jam
J16
Jam inside
J31, J32
Exit jam
J61, J62
ADF jam
J63
ADF exit jam
J72
Sorter jam
P20
Drum unit or toner level connection problem
P25
300 copies have been run since toner light came on. Depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
P26
Must adjust TDS in 47 mode
P64
ADF & operator are confused
P68, P69
ADF feed problem
P71
Sorter interlock
P81
Key counter not installed
Konica 1018
Код ошибки
Описание
F18
Paper lift did not complete
F23
Toner motor
F24
Pre clean lamp problem
F26
Toner density sensor
F34
Fuser overheat
F35
Fuser temperature too low. Lamp, thermofuse open wire
F36
Fuser temperature erratic. Probably thermistor
F41
End of scan sensor not actuated
F42
End of scan sensor not reached
F43
CVR (copy lamp voltage regulator)
F45
Lens or mirror movement problem
F52
Drive problem
F55
Zero cross.
F56
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60
ADF/machine interface problem
F67
ADF drive problem
F70
Sorter/machine interface problem
F77
Sorter bin problem
F78
Stapler problem
F86
Waste toner see 56
F98
Duplex problem
J11
Upper cassette
J12
Lower cassette
J13, J14
Paper feed jam
J15
Duplex unit jam
J16, J17
Feed jam
J19
Paper feed jam
J31, J32
Exit jam
J61
ADF opened during run
J62, J63
ADF jam
J65
RADF reverse jam
J72
Sorter jam, or sorter interlock opened
J75
Stapler jam
J92-J94
Duplex stack gate sensor or other duplex problem
J95
Duplex motor or duplex jam
P17
Right door
P19
Right door of paper feed unit
P20
Drum not installed properly or toner level sensor connection problem
P33
Left door
P61
RADF reverse cover open
P64
ADF was selected at the wrong time
P71
Sorter interlock
P74
Stapler overloaded, or paper left in stapler bin
P76
Out of staples
P81
Key counter not installed
P82
Memory card problem
P96
Paper in stacker when duplex selected
P97
Used bypass in duplex mode
P99
More than one side than the other in duplex
Konica 1112
Код ошибки
Описание
16
Feed jam
20
Toner level detector problem or loose connection
23
Toner feed problem
25
Toner. Means that 100 copies have been made since toner light came on
26
Toner density problem
31, 32
Exit jam
34
Fuser temperature too high
35
Fuser temperature too low
36
Fuser problem. Heat, thermistor, etc.
41
Scan return
42
Scan forward
43
Exposure lamp
50
Problem with IC8
52
EnКод ошибкиr (pulse sensor, PT; drive problem)
Konica 1120
Код ошибки
Описание
04
PTC heater. Don't know what this is, but "0" means it is not installed. 1 means it is.
F09
Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode" and select "P49" and reset to "0"
F23
Toner motor
F26
Toner density adjustment problem. This means the machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel you should disconnect the toner motor first. This Код ошибки happens probably because either the machine wasn't set up properly, or because the customer kept using the machine with the light on.
F28
Corona problem. Could be any corona.
F34
High fuser temperature.
F35, F36
Low fuser temperature.
F41, F42
Scan home
F43
Exposure lamp or exp. Lamp board.
F44
Lens drive problem.
F45
Lens problem.
F54
Fan motor.
F60
ADF to main board communication problem.
F67
ADF enКод ошибкиr (pulse sensor, drive problem)
F70
Sorter to machine communication problem.
F77
Sorter gate.
F88
AE adjustment problem.
J11-J13
Feed jam
J14-J16
Jam inside
J31, J32
Exit jam
J61, J62
ADF jam
J63
ADF exit jam
J72
Sorter jam
P11
Count. For total count, select "0". For developer count, select "5".
P12
Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.
P15
Size priority. 0 is standard. 1 is a size priority.
P16
Paper size priority.
P19
Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.
P20
Drum unit or toner level connection problem. Most likely, a loose connection.
P22-P24
Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
P25
300 copies have been run since toner light came on, depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
P26
ADF border erase. 0 for none. 5 for 5mm.
P26
Must replace and calibrate developer.
P27
PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P27
Toner density sensor unplugged or toner density sensor problem.
P28
PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P64
ADF & operator are confused. Remove original.
P68, P69
ADF feed problem.
P71
Sorter interlock.
P81
Key counter not installed.
Konica 1212
Код ошибки
Описание
04
PTC heater. Don't know what this is, but "0" means it is not installed. 1 means it is.
F09
Power leakage of some kind. Heat, exposure, AC or power supply or main relay. Go to "25 mode" and select "P49" and reset to "0"
F23
Toner motor
F26
Toner density adjustment problem. This means the machine is undertoned. To repair, replace developer and enter "47" mode. Press 51. Press print. Allow the machine to cycle until it stops. Some feel you should disconnect the toner motor first. This Код ошибки happens probably because either the machine wasn't set up properly, or because the customer kept using the machine with the light on.
F28
Corona problem. Could be any corona.
F34
High fuser temperature.
F35
Low fuser temperature.
F36
Low fuser temperature.
F41
Scan home
F43
Exposure lamp or exp. Lamp board.
F44
Lens drive problem.
F45
Lens problem.
F54
Fan motor.
F60
ADF to main board communication problem.
F67
ADF enКод ошибкиr (pulse sensor, drive problem)
F70
Sorter to machine communication problem.
F77
Sorter gate.
F88
AE adjustment problem.
J11-J13
Feed jam
J14-J16
Jam inside
J31, J32
Exit jam
J61, J62
ADF jam
J63
ADF exit jam
J72
Sorter jam
P11
Count. For total count, select "0". For developer count, select "5".
P12
Preheat mode fuser temperature. 0 for 365 degrees. 1 for 374 degrees. 2 for 383 degrees.
P15
Size priority. 0 is standard. 1 is a size priority.
P16
Paper size priority.
P19
Preheat shut off timing. 0 for 1 hour. 1 for 2 hours. 2 for 3 hours.
P20
Drum unit or toner level connection problem. Most likely, a loose connection.
P22-P24
Kind of obscure. This sets the wait time for tuning intermittent test copies in a 36 mode test.
P25
300 copies have been run since toner light came on, depending on how 25 mode, Код ошибки 92 is set, machine may not work at all.
P26
ADF border erase. 0 for none. 5 for 5mm.
P26
Must replace and calibrate developer.
P27
PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P27
Toner density sensor unplugged or toner density sensor problem.
P28
PM cycle. 27 is for the 5th digit. 28 is for the fourth digit.
P64
ADF & operator are confused. Remove original.
P68, P69
ADF feed problem.
P71
Sorter interlock.
Konica 1290, 1290RE
Код ошибки
Описание
16
Feed jam
20
Toner sensor connector
25
Toner light has been on for 100 copies
26
Toner density sensor
31
Exit switch not actuated
32
Exit jam
34
Fuser problem
35
Low fuser temperature
36
High fuser temperature
41
Scan did not return home
42
Scan problem
43
Exposure lamp problem
50
Board problem
52
Drive problem
85
No waste bottle
Konica 1590
Код ошибки
Описание
F23
Toner motor problem
F24
Pre-clean lamp
F26
Toner ratio
F34
High fuser temperature
F35
Low fuser temperature
F36
Thermistor
F41
Scan home
F42
Forward scan exposure lamp
F43
Exposure lamp
F45
Lens drive
F50
Board problem
F52
Drive
F77
Sorter bin sensor
J12, J13
Paper feed jam
J16
Paper feed jam
J31
Jam under drum
J32
Exit jam
J72
Sorter jam
P20
Drum not installed properly
P71
Sorter cover
Konica 1790
Код ошибки
Описание
F34
High fuser temperature
F35
Low fuser temperature
F36
Open thermistor or incomplete warm up
F41
Scan home problem
F42
Scan problem
F43
CVR board problem
F45
Lens drive
F52
Drive
F55
Zero cross problem
F67
ADF drive
F77
Sorter drive
J11
Upper cassette jam
J12
Lower cassette jam
J14
LCT jam
J16
Cassette jam
J31, J32
Jam under drum
J62, J63
ADF jam
J72
Sorter jam
P14
LCT open
P61
ADF up
P64
Original on glass
P69
ADF original jam
P71
Sorter cover open
P81
Key counter out
Konica 2020
Код ошибки
Описание
F18
Paper lift did not complete
F23
Toner motor
F24
Pre clean lamp problem
F26
Toner density sensor
F34
Fuser overheat
F35
Fuser temperature too low. Lamp, thermofuse open wire
F36
Fuser temperature erratic. Probably thermistor
F41
End of scan sensor not actuated
F42
End of scan sensor not reached
F43
CVR (copy lamp voltage regulator)
F45
Lens or mirror movement problem
F52
Drive problem
F55
Zero cross.
F56
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60
ADF/machine interface problem
F67
ADF drive problem
F70
Sorter/machine interface problem
F77
Sorter bin problem
F78
Stapler problem
F86
Waste toner see 56
F98
Duplex problem
J11
Upper cassette
J12
Lower cassette
J13, J14
Paper feed jam
J15
Duplex unit jam
J16, J17
Feed jam
J19
Paper feed jam
J31, J32
Exit jam
J61
ADF opened during run
J62, J63
ADF jam
J65
RADF reverse jam
J72
Sorter jam, or sorter interlock opened
J75
Stapler jam
J92-J94
Duplex stack gate sensor or other duplex problem
J95
Duplex motor or duplex jam
P17
Right door
P19
Right door of paper feed unit
P20
Drum not installed properly or toner level sensor connection problem
P33
Left door
P61
RADF reverse cover open
P64
ADF was selected at the wrong time
P71
Sorter interlock
P74
Stapler overloaded, or paper left in stapler bin
P76
Out of staples
P81
Key counter not installed
P82
Memory card problem
P96
Paper in stacker when duplex selected
P97
Used bypass in duplex mode
P99
More than one side than the other in duplex
Konica 2028
Код ошибки
Описание
F18
Paper lift did not complete
F23
Toner motor
F24
Pre clean lamp problem
F26
Toner density sensor
F34
Fuser overheat
F35
Fuser temperature too low. Lamp, thermofuse open wire
F36
Fuser temperature erratic. Probably thermistor
F41
End of scan sensor not actuated
F42
End of scan sensor not reached
F43
CVR (copy lamp voltage regulator)
F45
Lens or mirror movement problem
F52
Drive problem
F55
Zero cross
F56
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60
ADF/machine interface problem
F67
ADF drive problem
F70
Sorter/machine interface problem
F77
Sorter bin problem
F78
Stapler problem
F86
Waste toner see 56
F98
Duplex problem
J11
Upper cassette
J12
Lower cassette
J13, J14
Paper feed jam
J15
Duplex unit jam
J16, J17
Feed jam
J19
Paper feed jam
J31, J32
Exit jam
J61
ADF opened during run
J62, J63
ADF jam
J65
RADF reverse jam
J72
Sorter jam, or sorter interlock opened
J75
Stapler jam
J92-J94
Duplex stack gate sensor or other duplex problem
J95
Duplex motor or duplex jam
P17
Right door
P19
Right door of paper feed unit
P20
Drum not installed properly or toner level sensor connection problem
P33
Left door
P61
RADF reverse cover open
P64
ADF was selected at the wrong time
P71
Sorter interlock
P74
Stapler overloaded, or paper left in stapler bin
P76
Out of staples
P81
Key counter not installed
P82
Memory card problem
P96
Paper in stacker when duplex selected
P97
Used bypass in duplex mode
P99
More than one side than the other in duplex
Konica 2125
Код ошибки
Описание
F18
Paper feed lift problem
F18-3
LCT problem
F18-4
LCT problem
F28-1
Charge corona
F28-2
Transfer or separator corona
F34-1
High fuser temperature
F34-2
High fuser temperature
F35-1
Low fuser temperature
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F36-2
Low fuser temperature
F41
Scan return problem
F42
Scan forward problem
F43
Exposure lamp board problem
F45
Lens home problem
F52
Main motor drive problem
F55
Zero cross of DC power supply
F60
Communication interruption between the machine and RADF
F67
RDH or RADF drive problem
F70
Communication problem between machine and sorter
F77
Sorter bin problem
F78
No memory card installed
F86
Too many copies were made after toner waste was full. Reset with 47 mode, Код ошибки 94.
F98
Duplex guide plate does not return home quickly enough
J10
Feed jam
J11
Upper feed jam
J12
Lower feed jam
J13
Upper paper feed unit jam
J14, J15
Lower paper feed unit jam
J16, J17
Jam in machine
J19
Paper feed unit jam
J21
Jam around drum
J31
Exit jam
J32
Exit jam
J61, J62
RDH/RADF jam or open
J63
RADF exit jam
J72
Sorter jam or open interlock
J74
Finisher problem
J75
Stapler problem
J92-J95
Duplex jam
P17
Right side door open
P19
Paper feed unit door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P68
Original removed during operation of RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76
Out of staples
P78
Stapler not installed
P81
Key counter not plugged in
P82
Memory card not installed, not formatted to Konica specs, or no machine serial number registered on memory card
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Bypass was used or attempted during duplex.
P99
Too many reverse side copies during duplex
Konica 2130
Код ошибки
Описание
F18
Paper feed lift problem
F18-3
LCT problem
F18-4
LCT problem
F28-1
Charge corona
F28-2
Transfer or separator corona
F34-1
High fuser temperature
F34-2
High fuser temperature
F35-1
Low fuser temperature
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F36-2
Low fuser temperature
F41
Scan return problem
F42
Scan forward problem
F43
Exposure lamp board problem
F45
Lens home problem
F52
Main motor drive problem
F55
Zero cross of DC power supply
F60
Communication interruption between the machine and RADF
F67
RDH or RADF drive problem
F70
Communication problem between machine and sorter
F77
Sorter bin problem
F78
No memory card installed
F86
Too many copies were made after toner waste was full. Reset with 47 mode, Код ошибки 94.
F98
Duplex guide plate does not return home quickly enough
J10
Feed jam
J11
Upper feed jam
J12
Lower feed jam
J13
Upper paper feed unit jam
J14
Lower paper feed unit jam
J15
Lower paper feed unit jam
J16, J17
Jam in machine
J19
Paper feed unit jam
J21
Jam around drum
J31, J32
Exit jam
J61
RDH/RADF jam or open
J62
RDH/RADF jam
J63
RADF exit jam
J72
Sorter jam or open interlock
J74
Finisher problem
J75
Stapler problem
J92-J95
Duplex jam
P17
Right side door open
P19
Paper feed unit door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P68
Original removed during operation of RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76
Out of staples
P78
Stapler not installed
P81
Key counter not plugged in
P82
Memory card not installed, not formatted to Konica specs, or no machine serial number registered on memory card
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Bypass was used or attempted during duplex.
P99
Too many reverse side copies during duplex
Konica 2203
Код ошибки
Описание
F35
Low Temperature
F41, F42
Optics
F43
CVR
F46
Lens drive
F51
Door
F52
Drive
J11
Upper PF jam
J12
Lower PF jam
J13
Jam
J21
Separator jam
J31
Transport jam
J32
Jam
P81
Key counter
Konica 2290
Код ошибки
Описание
1
Sort jam
61
ADF/RADF open door
64
Original on glass
97
Duplex paper wrong size selected
99
Duplex fed double
F35, F36
Fuser
F41
Scan return
F42
Scan forward problem
F43
Exposure stays on
F46
Lens position problem
F52
Drive
F53
Developer unit shift problem
F67
ADF/RADF drive problem
F98
Duplex side to side gate problem
J11
Upper cassette jam
J12
Lower cassette jam
J13
LCT jam
J14
Jam
J15
Paper feed jam
J21
Jam under/around drum
J31
Transport jam
J32
Exit ajm
J61
RADF jam
J62
ADF
J63
ADF exit jam
J65
ADF
J72
Sort jam
J92-J96
Duplex jams
P81
Key counter
Konica 2590
Код ошибки
Описание
F34
High fuser temperature
F35
Low fuser temperature at warm up
F36
Low fuser temperature after warm up
F41
No scan
F42
No return scan
F43
Exposure lamp stays on
F45
Lens
F52
Drive
F55
Zero cross signal to main board
F67
ADF drive
F77
Sorter drive
F98
Duplex problem
J11
Bypass jam
J12
Middle cassette jam
J13
Lower cassette jam
J14
LCT jam
J15
Duplex jam
J16
Paper feed jam
J17
Registration jam
J31
Internal jam
J32
Exit jam
J61
ADF opened during runADF jam
J62, J63
ADF exit jam
J65
RADF jam
J72
Sorter jam
J92-J96
Duplex jams
P14
LCT cover open
P61
RADF cover open
P64
Original on glass
P69
RADF jam in sheet feet mode
P71
Sorter cover open
P81
Key counter
P96
Paper still in duplex tray
P97
Wrong size selected for duplex
P99
Duplex confused by double fed originals
Konica 3035
Код ошибки
Описание
F18
Paper lift did not complete
F23
Toner motor
F24
Pre clean lamp problem
F26
Toner density sensor
F34
Fuser overheat
F35
Fuser temperature too low. Lamp, thermofuse open wire
F36
Fuser temperature erratic. Probably thermistor
F41
End of scan sensor not actuated
F42
End of scan sensor not reached
F43
CVR (copy lamp voltage regulator)
F45
Lens or mirror movement problem
F52
Drive problem
F55
Zero cross
F56
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60
ADF/machine interface problem
F67
ADF drive problem
F70
Sorter/machine interface problem
F77
Sorter bin problem
F78
Stapler problem
F86
Waste toner see 56
F98
Duplex problem
J11
Upper cassette
J12
Lower cassette
J13, J14
Paper feed jam
J15
Duplex unit jam
J16, J17
Feed jam
J19
Paper feed jam
J31, J32
Exit jam
J61
ADF opened during run
J62, J63
ADF jam
J65
RADF reverse jam
J72
Sorter jam, or sorter interlock opened
J75
Stapler jam
J92-J94
Duplex stack gate sensor or other duplex problem
J95
Duplex motor or duplex jam
P17
Right door
P19
Right door of paper feed unit
P20
Drum not installed properly or toner level sensor connection problem
P33
Left door
P61
RADF reverse cover open
P64
ADF was selected at the wrong time
P71
Sorter interlock
P74
Stapler overloaded, or paper left in stapler bin
P76
Out of staples
P81
Key counter not installed
P82
Memory card problem
P96
Paper in stacker when duplex selected
P97
Used bypass in duplex mode
P99
More than one side than the other in duplex
Konica 3135
Код ошибки
Описание
F18
Paper feed lift problem
F18-3
LCT problem
F18-4
LCT problem
F28-1
Charge corona
F28-2
Transfer or separator corona
F34-1
High fuser temperature
F34-2
High fuser temperature
F35-1
Low fuser temperature
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F36-2
Low fuser temperature
F41
Scan problem
F42
Scan forward problem
F43
Exposure lamp board problem
F45
Lens home problem
F52
Main motor drive problem
F55
Zero cross of DC power supply
F60
Communication interruption between machine and RADF
F67
RDH or RADF drive problem
F70
Communication problem between machine and sorter
F77
Sorter, finisher, or stapler problem
F86
Too many copies were made after toner waste was full
F98
Duplex problem
J10
Feed jam
J11, J12
Jam in machine
J13
LCT jam
J14
LCT jam
J15
Duplex feed jam
J16, J17
Jam in machine
J19
LCT jam
J21
Jam around drum
J31
Jam in machine
J32
Exit jam
J61, J62
RDH/RADF jam
J63
RADF exit jam
J72
Sorter jam or open interlock
J74
Finisher problem
J75
Stapler problem
J92
Duplex jam
J93
Duplex jam
J94
Duplex jam
J95
Duplex jam
P17
Paper feed door open
P19
LCT door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P64
RDH original width different with guide width
P68
Original removed during operation or RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
P76
No staples
P78
Stapler not installed
P81
Key counter not plugged in
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Wrong size paper during duplex
P99
Too many reverse side copies during duplex.
Konica 3240
Код ошибки
Описание
F10-1
Paper feed or duplex communication problem
F10-2
Paper feed or duplex communication problem
F10-3
Paper feed unit connection problem
F10-4
Internal temperature problem
F18-1
Upper feed lift problem
F18-2
Lower paper feed lift problem
F18-3
Upper paper feed lift problem
F18-4
Middle paper feed unit problem
F18-5
Lower paper feed unit lift problem
F28-1
Transfer separator corona
F28-2
Charge corona
F34-1
High fuser temperature or bad thermistor
F34-2
High fuser temperature
F35-1
Low fuser temperature or open thermistor
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F42-1
Scan forward problem
F42-2
Scan home problem
F42-3
Scan problem
F43-1
Exposure lamp board problem
F43-2
Exposure lamp board problem
F43-3
Exposure lamp board problem
F44-1
Optics communication problem
F45-1
Lens home problem
F45-2
Mirror home problem
F51-2
Main motor speed problem
F52-1
Cooling fan problem
F52-2
Suction (transport) fan problem
F52-4
Optics cooling fan problem (2 fans; could be either one)
F60
Communication interruption between machine and RADF
F67
RDH or RADF pressure home sensor or pressure motor.
F70
Communication problem between machine and sorter
F76
Stapler problem
F77
Sorter bin problem
F78
No memory card installed
F80
Communication problem between machine and weekly timer
F81
Communication problem between machine and memory card
F97
Duplex up down plate problem
F98
Duplex guide plate problem
F99
Duplex indexer problem
J10
Feed jam
J11
Upper feed jam
J12
Lower feed jam
J13
Upper paper feed unit jam
J14
Lower paper feed unit jam
J15
Duplex feed jam
J17
Jam in machine
J17-7
Jam at paper feed unit exit
J18
Jam in machine from middle tray of paper feed unit
J31, J32
Exit jam
J61
RADF opened during run, or other RADF jam
J62
RDH/RADF jam
J63
RADF feed jam
J72
Sorter jam or open interlock
J74
Finisher problem
J75
Stapler problem
J92
Reversal sensor jam
J97-1
Stacker entrance jam
J97-2
Stacker entrance jam
J98
Stacker entrance jam
P17
Right side door open
P19
Paper feed unit door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P68
Original removed during operation of the RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went to the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76
Out of staples
P78
Stapler not installed
P81
Key counter not plugged in
P82
Memory card not installed, not formatted to Konica specs, or no machine serial # registered on memory card.
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Bypass was used or attempted during duplex
P99
Too many reverse side copies during duplex
Konica 3290
Код ошибки
Описание
51
Door open
64
Original still on glass
71
Sorter interlock
91
Duplex interlock
97
Incorrect mode selected
99
Duplex problem
F35
Fuser
F41
Scan return
F42
Scan
F43
Exposure lamp
F46
Lens drive
F52
Machine drive
F67
RADF
F98
Duplex unit
J11
Upper cassette jam
J12
Lower cassette jam
J13
LCT jam
J14
Paper feed jam
J15
Duplex jam
J21
Drum wrap jam
J31
Transport jam
J32
Fuser jam
J61
RADF cover
J62
RADF feed
J63
RADF exit
J65
RADF jam
J72
Sorter jam
J94-J96
Duplex jam or paper still in duplex unit
P81
Key counter
Konica 3340
Код ошибки
Описание
F10-1
Paper feed or duplex communication problem
F10-2
Paper feed or duplex communication problem
F10-3
Paper feed unit connection problem
F10-4
Internal temperature problem
F18-1
Upper feed lift problem
F18-2
Lower paper feed lift problem
F18-3
Upper paper feed lift problem
F18-4
Middle paper feed unit problem
F18-5
Lower paper feed unit lift problem
F28-1
Transfer separator corona
F28-2
Charge corona
F34-1
High fuser temperature or bad thermistor
F34-2
High fuser temperature
F35-1
Low fuser temperature or open thermistor
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F42-1
Scan forward problem
F42-2
Scan home problem
F42-3
Scan problem
F43-1
Exposure lamp board problem
F43-2
Exposure lamp board problem
F43-3
Exposure lamp board problem
F44-1
Optics communication problem
F45-1
Lens home problem
F45-2
Mirror home problem
F51-2
Main motor speed problem
F52-1
Cooling fan problem
F52-2
Suction (transport) fan problem
F52-4
Optics cooling fan problem (2 fans; could be either one)
F60
Communication interruption between machine and RADF
F67
RDH or RADF pressure home sensor or pressure motor.
F70
Communication problem between machine and sorter
F76
Stapler problem
F77
Sorter bin problem
F78
No memory card installed
F80
Communication problem between machine and weekly timer
F81
Communication problem between machine and memory card
F97
Duplex up down plate problem
F98
Duplex guide plate problem
F99
Duplex indexer problem
J10
Feed jam
J11
Upper feed jam
J12
Lower feed jam
J13
Upper paper feed unit jam
J14
Lower paper feed unit jam
J15
Duplex feed jam
J17
Jam in machine
J17-7
Jam at paper feed unit exit
J18
Jam in machine from middle tray of paper feed unit
J31, J32
Exit jam
J61
RADF opened during run, or other RADF jam
J62
RDH/RADF jam
J63
RADF feed jam
J72
Sorter jam or open interlock
J74
Finisher problem
J75
Stapler problem
J92
Reversal sensor jam
J97-1
Stacker entrance jam
J97-2
Stacker entrance jam
J98
Stacker entrance jam
P17
Right side door open
P19
Paper feed unit door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P68
Original removed during operation of the RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went to the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode, or more than 25 copies per bin were attempted by the stapler.
P76
Out of staples
P78
Stapler not installed
P81
Key counter not plugged in
P82
Memory card not installed, not formatted to Konica specs, or no machine serial # registered on memory card.
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Bypass was used or attempted during duplex
Konica 4045
Код ошибки
Описание
F18
Paper lift did not complete
F23
Toner motor
F24
Pre clean lamp problem
F26
Toner density sensor
F34
Fuser overheat
F35
Fuser temperature too low. Lamp, thermofuse open wire
F36
Fuser temperature erratic. Probably thermistor
F41
End of scan sensor not actuated
F42
End of scan sensor not reached
F43
CVR (copy lamp voltage regulator)
F45
Lens or mirror movement problem
F52
Drive problem
F55
Zero cross.
F56
Waste toner collector box is full. After replacing it, you must enter Код ошибки 94 in the 47 mode to reset
F60
ADF/machine interface problem
F67
ADF drive problem
F70
Sorter/machine interface problem
F77
Sorter bin problem
F78
Stapler problem
F86
Waste toner see 56
F98
Duplex problem
J11
Upper cassette
J12
Lower cassette
J13, J14
Paper feed jam
J15
Duplex unit jam
J16, J17
Feed jam
J19
Paper feed jam
J31, J32
Exit jam
J61
ADF opened during run
J62, J63
ADF jam
J65
RADF reverse jam
J72
Sorter jam, or sorter interlock opened
J75
Stapler jam
J92-J94
Duplex stack gate sensor or other duplex problem
J95
Duplex motor or duplex jam
P17
Right door
P19
Right door of paper feed unit
P20
Drum not installed properly or toner level sensor connection problem
P33
Left door
P61
RADF reverse cover open
P64
ADF was selected at the wrong time
P71
Sorter interlock
P74
Stapler overloaded, or paper left in stapler bin
P76
Out of staples
P81
Key counter not installed
P82
Memory card problem
P96
Paper in stacker when duplex selected
P97
Used bypass in duplex mode
P99
More than one side than the other in duplex
Konica 4065
Код ошибки
Описание
11-1
Paper feed jam
11-10
RADF jam
11-11
Sorter jam
11-12
Sorter jam
11-2
Paper feed jam
11-3
Registration area jam
11-4
Paper jam around drum (drum wrap jam)
11-5
Jam in transport area
11-6
Exit jam or duplex exit jam
11-7
Duplex reversing sensor jam or duplex feed jam
11-8
Duplex jam
11-9
Duplex jam
Konica 4145
Код ошибки
Описание
F18
Paper feed lift problem
F18-3
LCT problem
F18-4
LCT problem
F28-1
Charge corona
F28-2
Transfer or separator corona
F34-1
High fuser temperature
F34-2
High fuser temperature
F35-1
Low fuser temperature
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F36-2
Low fuser temperature
F41
Scan problem
F42
Scan forward problem
F43
Exposure lamp board problem
F45
Lens home problem
F52
Main motor drive problem
F55
Zero cross of DC power supply
F60
Communication interruption between machine and RADF
F67
RDH or RADF drive problem
F70
Communication problem between machine and sorter
F77
Sorter, finisher, or stapler problem
F86
Too many copies were made after toner waste was full
F98
Duplex problem
J10
Feed jam
J11, J12
Jam in machine
J13
LCT jam
J14
LCT jam
J15
Duplex feed jam
J16, J17
Jam in machine
J19
LCT jam
J21
Jam around drum
J31
Jam in machine
J32
Exit jam
J61, J62
RDH/RADF jam
J63
RADF exit jam
J72
Sorter jam or open interlock
J74
Finisher problem
J75
Stapler problem
J92-J95
Duplex jam
P17
Paper feed door open
P19
LCT door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P64
RDH original width different with guide width
P68
Original removed during operation or RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
P76
No staples
P78
Stapler not installed
P81
Key counter not plugged in
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Wrong size paper during duplex
P99
Too many reverse side copies during duplex.
Konica 4155
Код ошибки
Описание
F18
Paper feed lift problem
F18-3
LCT problem
F18-4
LCT problem
F28-1
Charge corona
F28-2
Transfer or separator corona
F34-1
High fuser temperature
F34-2
High fuser temperature
F35-1
Low fuser temperature
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F36-2
Low fuser temperature
F41
Scan problem
F42
Scan forward problem
F43
Exposure lamp board problem
F45
Lens home problem
F52
Main motor drive problem
F55
Zero cross of DC power supply
F60
Communication interruption between machine and RADF
F67
RDH or RADF drive problem
F70
Communication problem between machine and sorter
F77
Sorter, finisher, or stapler problem
F86
Too many copies were made after toner waste was full
F98
Duplex problem
J10
Feed jam
J11
Jam in machine
J12
Jam in machine
J13, J14
LCT jam
J15
Duplex feed jam
J16, J17
Jam in machine
J19
LCT jam
J21
Jam around drum
J31
Jam in machine
J32
Exit jam
J61, J62
RDH/RADF jam
J63
RADF exit jam
J72
Sorter jam or open interlock
J74
Finisher problem
J75
Stapler problem
J92-J95
Duplex jam
P17
Paper feed door open
P19
LCT door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P64
RDH original width different with guide width
P68
Original removed during operation or RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
P76
No staples
P78
Stapler not installed
P81
Key counter not plugged in
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Wrong size paper during duplex
P99
Too many reverse side copies during duplex.
Konica 4255
Код ошибки
Описание
F18
Paper feed lift problem
F18-3
LCT problem
F18-4
LCT problem
F28-1
Charge corona
F28-2
Transfer or separator corona
F34-1
High fuser temperature
F34-2
High fuser temperature
F35-1
Low fuser temperature
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F36-2
Low fuser temperature
F41
Scan problem
F42
Scan forward problem
F43
Exposure lamp board problem
F45
Lens home problem
F52
Main motor drive problem
F55
Zero cross of DC power supply
F60
Communication interruption between machine and RADF
F67
RDH or RADF drive problem
F70
Communication problem between machine and sorter
F77
Sorter, finisher, or stapler problem
F86
Too many copies were made after toner waste was full
F98
Duplex problem
J10
Feed jam
J11, J12
Jam in machine
J13, J14
LCT jam
J15
Duplex feed jam
J16, J17
Jam in machine
J19
LCT jam
J21
Jam around drum
J31
Jam in machine
J32
Exit jam
J61, J62
RDH/RADF jam
J63
RADF exit jam
J72
Sorter jam or open interlock
J74
Finisher problem
J75
Stapler problem
J92-J95
Duplex jam
P17
Paper feed door open
P19
LCT door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P64
RDH original width different with guide width
P68
Original removed during operation or RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in the staple mode
P76
No staples
P78
Stapler not installed
P81
Key counter not plugged in
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Wrong size paper during duplex
Konica 4290
Код ошибки
Описание
B81
Key counter
F36
CA
F41
Optics forward
F42
Optics return
F43
CVR
F45
Lens drive
F46
Magnification data
F47
Mode data
F52
Drive
F56
Data transfer (CPU)
F57
Data transfer (RADF & Control Board)
F59
Pressure cam
F67
RADF drive
F73
Bin alarm
F98
Duplex unit
J11
Upper cassette jam
J12
Middle cassette jam
J13
Lower cassette jam
J15
Duplex 2nd side PF jam
J16
Jam before drum
J21
Drum wrap jam
J31
Conveyance jam
J32
Exit jam
J44
Jam
J61
RADF open
J62
RADF feed jam
J63
RADF exit jam
J65
RADF reversal jam
J72
Sorter jam
J92
Duplex unit inlet jam
J93
Duplex unit reverse jam
J94
Duplex unit conveyance jam
J95
Duplex unit conveyance jam
P10
Cassette end
P51
Door open
P61
RADF door
P64
Paper in ADF
P71
Sorter door
P91
Duplex door
P96
Paper in ADF
P97
Wrong cassette selected in duplex
Konica 4345
Код ошибки
Описание
F18-1
Upper paper feed problem
F18-2
Lower paper feed problem
F18-3
Upper paper feed unit or LCT lift problem
F18-4
Lower paper feed unit or LCT lift problem
F23
Toner motor problem
F28-2
Transfer corona or toner motor problem
F34-1
High fuser temperature or bad thermistor
F34-2
High fuser temperature
F35-1
Low fuser temperature or open thermistor
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F36-2
Low fuser temperature
F41-1
Scan return problem
F41-2
Scan overrun problem
F41-3
Scan problem
F41-4
Glass detector problem
F42-1
Scan forward problem
F42-2
Scan home problem
F43
Exposure lamp board problem
F45-1
Lens home problem
F45-2
Mirror home problem
F49
Optics fan
F52
Main motor drive problem
F54
Cooling fan
F55
Zero cross. Could be upper tray limit sensor
F60
Communication problem between the machine and ADF
F67
ADF drive problem
F70
Communication problem between machine and sorter
F77-1
Sorter problem
F77-2
Sorter bin shift
F77-3
Sorter guide bar or vibration motor
F77-4
Stapler vibrator motor problem
F78
No memory card installed
F98
Duplex guide plate problem
J10
Feed jam
J11
Upper feed jam
J12
Feed jam
J13
Upper paper feed unit or LCT jam
J14
Lower paper feed unit or LCT jam
J15
Duplex feed jam
J16, J17
Jam in machine
J19
Jam in LCT
J21
Drum wrap jam
J31, J32
Exit jam
J61
RADF opened during run, or other RADF jam
J62
RADF feed jam
J63
RADF inversion jam
J72
Sorter jam
J75
Stapler problem
J92
Sorter jam
J93
Sorter problem
J94, J95
Duplex jam
P17
Right side door open
P19
Paper feed unit door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P68
Original removed during operation of RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in staple mode, or more than 25 copies per bin were attempted by the stapler
P76
Out of staples
P78
Stapler not installed
P81
Key counter not plugged in
P82
Memory card not installed, not formatted to Konica specs, or no machine serial # registered on the memory card.
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Bypass was used or attempted during duplex.
P99
Too many reverse side copies during duplex.
Konica 4355
Код ошибки
Описание
F18-1
Upper paper feed problem
F18-2
Lower paper feed problem
F18-3
Upper paper feed unit or LCT lift problem
F18-4
Lower paper feed unit or LCT lift problem
F23
Toner motor problem
F28-2
Transfer corona or toner motor problem
F34-1
High fuser temperature or bad thermistor
F34-2
High fuser temperature
F35-1
Low fuser temperature or open thermistor
F35-2
Low fuser temperature
F36-1
Low fuser temperature
F36-2
Low fuser temperature
F41-1
Scan return problem
F41-2
Scan overrun problem
F41-3
Scan problem
F41-4
Glass detector problem
F42-1
Scan forward problem
F42-2
Scan home problem
F43
Exposure lamp board problem
F45-1
Lens home problem
F45-2
Mirror home problem
F49
Optics fan
F52
Main motor drive problem
F54
Cooling fan
F55
Zero cross. Could be upper tray limit sensor
F60
Communication problem between the machine and ADF
F67
ADF drive problem
F70
Communication problem between machine and sorter
F77-1
Sorter problem
F77-2
Sorter bin shift
F77-3
Sorter guide bar or vibration motor
F77-4
Stapler vibrator motor problem
F78
No memory card installed
F98
Duplex guide plate problem
J10
Feed jam
J11
Upper feed jam
J12
Feed jam
J13
Upper paper feed unit or LCT jam
J14
Lower paper feed unit or LCT jam
J15
Duplex feed jam
J16, J17
Jam in machine
J19
Jam in LCT
J21
Drum wrap jam
J31, J32
Exit jam
J61
RADF opened during run, or other RADF jam
J62
RADF feed jam
J63
RADF inversion jam
J72
Sorter jam
J75
Stapler problem
J92
Sorter jam
J93
Sorter problem
J94, J95
Duplex jam
P17
Right side door open
P19
Paper feed unit door open
P33
Exit door open
P51
Front door open
P61
RADF cover open
P64
RADF not opened to remove originals
P68
Original removed during operation of RADF
P69
Original didn't feed during RADF/RDH operation
P71
Sorter interlock
P74
51 copies or more went into the stapler or paper was in the sorter/stapler, or different size originals were used in staple mode, or more than 25 copies per bin were attempted by the stapler
P76
Out of staples
P78
Stapler not installed
P81
Key counter not plugged in
P82
Memory card not installed, not formatted to Konica specs, or no machine serial # registered on the memory card.
P86
No toner waste box
P91
Duplex unit pulled out
P96
Paper in duplex tray
P97
Bypass was used or attempted during duplex.
P99
Too many reverse side copies during duplex.
Konica 5080, 6090, 7490
Код ошибки
Описание
11-1
Paper feed jam
11-10
RADF jam
11-11
Sorter jam
11-12
Sorter jam
11-2
Paper feed jam
11-3
Registration area jam
11-4
Paper jam around drum (drum wrap jam)
11-5
Jam in transport area
11-6
Exit jam or duplex exit jam
11-7
Duplex reversing sensor jam or duplex feed jam
11-8
Duplex jam
11-9
Duplex jam
Если Вы не смогли найти своей модели в этом разделе, то есть вероятность, что Ваш аппарат является аналогом одного из представленных здесь. Проверить это можно в разделе "Совместимость".
Коды ошибок копиров ("ксероксов"), Konica