Коды ошибок аналоговых копиров ("ксероксов") Sharp
Коды ошибок аналоговых Коды ошибок аналоговых копировальных аппаратов Sharp копировальных аппаратов Sharp
Если Ваш аналоговый копировальный аппарат Sharp выдал на индикации некий код, то узнать причину возникновения ошибки Вы можете в этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарата; а о том, как устранить сам сбой, есть много материалов в разделах "Ремонт", "Ликбез", "FAQ"; также Вы можете воспользоваться поиском или указателем материалов сайта
Sharp 1420, 1430
Код ошибки
Описание
A1
Jam in document feeder
A2
Jam in document feeder
C1
Cassette misfeed
C2
Cassette feed, bypass unplugged
C3
Bypass misfeed
E1
Paper feed jam
E3
Exit jam
EE-EL
Developer overtoned during setup
EE-EU
Developer undertoned during setup
J0
Developer setup taking place
J1
Add toner
J3
Drum unit not installed properly or missing
J7
Drum unit due for replacing
J8
Wrong drum unit or power was turned on after J7 displayed
L6
Key counter or other optional counter accessory problem
U1
Drive problem
U2
Scan
U3
Lens
U4-01
Fuser thermistor
U4-02
High fuser temperature
U4-03
Low fuser temperature
U5
500 sheet cassette lift motor
U6
Main board problem
U7
Document glass too hot (with document feeder)
U8
Problem with line voltage
U9
Auto developer setup problem
Sharp 2014
Код ошибки
Описание
A1
Jam in document feeder
A2
Jam in document feeder
C1
Cassette misfeed
C2
Cassette feed, bypass unplugged
C3
Bypass misfeed
E1
Paper feed jam
E3
Exit jam
EE-EL
Developer overtoned during setup
EE-EU
Developer undertoned during setup
H2-0
Fusing unit temperature error
H3-0
Overheated fusing unit
H4-0
The fusing unit doesn't heat up
J0
Developer setup taking place
J1
Add toner
J3
Drum unit not installed properly or missing
J7
Drum unit due for replacing
J8
Wrong drum unit or power was turned on after J7 displayed
L1-0
Scanner position error
L3-0
Scanner position error
L4-1
Main motor drive overloaded
L5-2
Lens position error
L6
Key counter or other optional counter accessory problem
L8-1
Zero cross signal error
L8-3
Auto-exposure sensor malfunction
U1
Drive problem
U2
Scan
U3
Lens
U4-01
Fuser thermistor
U4-02
High fuser temperature
U4-03
Low fuser temperature
U5
500 sheet cassette lift motor
U6
Main board problem
U7
Document glass too hot (with document feeder)
U8
Problem with line voltage
U9
Auto developer setup problem
Sharp 2020
Код ошибки
Описание
CC
Original detection problem
CH
Lit Steadily: Sorter not installed, or not turned on
CH
Flashing: DV unit not installed, not connected properly, or not latched in place properly
F1
Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport motor drive.
F2
Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark sensor problem. . Does not see mark on drum or sensor not working properly.
H2
Sub code 00: Fuser thermistor open.
H3
Sub code 00: Fuser temperature too high.
H4
Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections.
L1
Scan forward problem. Motor, sensor, board
L3
Scan forward problem. Motor, sensor, board.
L4
Drive problem; main motor, gear, sensor, bind.
L5
Lens problem. Motor sensor board.
L8
Sub code 01: Zero cross.
P
Paper feed problem or no paper
PC
Card counter not installed
U2
Sub code 01: Memory loss.
U4
Sub code 00: Communication problem between copier and duplex unit.
U5
Sub code 00: Communication problem between main board and ADF.
Sharp 2022, 2027, 2035
Код ошибки
Описание
P10
Set or clear departmental counter
P11
Display individual departmental counts
P13
Clear departmental counters
P14
Enter, clear or change department numbers
P16
Change max. number of copies that can be run
P18
Sends alarm if the wrong department number is tried three times in a row
P19
Change code number
P20
Adjust auto exposure
P21
Adjust automautic shufoff
P22
Adjust manual exposure
P23
Adjust auto clear time
P24
Set up fixed magnification settings
P25
Set maximum number of copies or of sets
P26
Binding margin
P27
Border erase setting
P28
Defaults at power on
P29
Display various counts
P30
Auto repeat on or off
P45
Message display time
P70
Auto paper select on or off
P71
Auto cassette select on or off
P72
Maximum copies in duplex
P73
Copy condition in rewrite
P74
Duplex limit when problems with duplex unit
P75
Prevent auto duplex
P76
Prevent stapling
P77
Prevent cover use
P90
List programs
Sharp 2025, 2030, 2040
Код ошибки
Описание
C2
Transfer corona problem or HVT
CC
Original detection problem.
CH
Door open or developer unit not installed, not connected properly, or not latched in place properly.
F1
Sub code 00: Communication error between main board and sorter. 01: Jogger error. 02: Sorter transport motor drive. 04: Sorter bin sensor problem. Lower limit sensed wrong.
F2
Sub code 02: Toner motor problem. 31: Image density sensor problem. Could be a problem with the light level. 32: Drum mark sensor problem. Does not see mark on drum or sensor does not work properly. 35: Grid voltage correction will not work during simulation.
F3
Sub code 12: Copier upper cassette lift motor problem. Copier bottom cassette lift motor problem.
H2
Fuser thermistor open.
H3
Fuser temperature too high.
H4
Fuser temperature too low. Lamp, thermal switch, connections.
L4
Sub code 01: Drive problem, main motor, sensor, bind.
L5
Sub code 03: Drive problem with 4th/5th mirror assembly, motor, sensor, board.
L8
Sub code 01: Power frequency problem.
PC
Card counter or key counter not installed.
PF
There is an inhibit command from the PC modem. This is reset with simulation 17.
U2
Sub code 00 or 01: Memory error.
U3
Sub code 20: Mirror motor locked. 21: Mirror motor home sensor.
U4
Sub code 02: Duplex alignment plate out of position motor, cable, sensor.
U5
Sub code 00: Communication problem between main board and RADF. 01: RADF motor drive problem. 02: RADF motor drive problem. 03: RADF resist sensor. 04: RADF exit sensor.
U6
Sub code 00: Communication error between copier and desk. 01, 02, 03: Desk lift motor drive problem. 08: Desk 24v problem. 09: LCT motor overload. 10: Desk transport motor drive problem.
U7
Sub code 00: Communication problem between copier and PC modem.
Sharp 2050
Код ошибки
Описание
CC-nn
Original sensing problem
CH
Lit steadily: Door open
CH
Flashing: Developer unit not installed, not latched or not installed properly
EE-EL
During developer calibration, overtoned condition detected
EE-EU
During developer calibration, undertoned condition detected
F1-00
Communication problem between main board and stapler
F1-02
Stapler sorter transport drive problem
F1-03
Problem with guide bar oscillator motor
F1-04
Index lower sensor
F1-05
Index upper sensor
F1-06
Shift motor problem in stapler sorter, or index motor problem
F1-08
Staple sorter shift motor drive problem
F1-10
Stapler problem
F2-00
Toner sensor problem
F2-31
Drum surface reflecting problem
F2-32
Drum sensor not scanning mark properly
F2-33
Grid voltage is too high or too low
F2-35
During patch detection, measurement is wrong
F2-37
Drum mark sensor adjustment problem
F3-01
LCT encoder
F3-02
LCT lift problem
F3-03
LCT down problem
F3-12
Cassette 1 lift problem
F3-22
Cassette 2 lift problem
F3-32
Cassette 3 lift problem
F3-42
Cassette 4 lift problem
H2-00
Fuser thermistor
H3-00
Fuser temperature too high
H4-00
Fuser temperature too low
L1-00
Scan problem
L2-00
Mirror motor drive problem
L3-00
Scan return problem
L4-01
Drum motor drive problem
L4-02
Main motor drive problem
L5-00
4/5 mirror drive problem
L8-01
Full wave signal missing to auto exposure
L8-02
Full wave signal to auto exposure is incorrect
L8-03
During auto exposure adjust procedure, the auto exp.
P20
Adjust automatic exposure
P21
Auto shut off timing
P22
Toner save mode
P25
Maximum number of copies that can be selected
P26
Margin shift
P28
Initial status
P29
To read total copies
P70
Auto paper select
P72
Bypass in duplex
P74
Stop document feeder use
P75
Stop duplex use
P76
Stop stapler use
P83
Modem access to codes through phone line
P90
Display all of the operator programs
PC
Card counter
PF
Modem problem
U0-00
Operation panel problem
U2-00
EEPROM error. Reset with sim. 16
U3-00
Communication problem between master and mirror controller
U3-20
Mirror drive problem
U3-21
Mirror home sensor problem
U3-26
Mirror motor voltage problem
U3-41
Lens motor home correction did not go well
U3-42
4/5 mirror motor problem similar to U3 -41
U4-02
Duplex alignment plate sensor
U4-03
Duplex rear plate sensor
U5-00
Communication problem between RADF and copier
U5-01
RADF resist sensor
U5-02
RADF reverse sensor
U5-03
RADF timing sensor
U5-04
RADF empty sensor
U5-11
RADF paper feed drive problem
U5-12
RADF transport drive problem
U7-00
Communication problem between copier and modem
Sharp 2114
Код ошибки
Описание
A1
Jam in document feeder
A2
Jam in document feeder
C1
Cassette misfeed
C2
Cassette feed, bypass unplugged
C3
Bypass misfeed
E1
Paper feed jam
E3
Exit jam
EE-EL
Developer overtoned during setup
EE-EU
Developer undertoned during setup
J0
Developer setup taking place
J1
Add toner
J3
Drum unit not installed properly or missing
J7
Drum unit due for replacing
J8
Wrong drum unit or power was turned on after J7 displayed
L6
Key counter or other optional counter accessory problem
U1
Drive problem
U2
Scan
U3
Lens
U4-01
Fuser thermistor
U4-02
High fuser temperature
U4-03
Low fuser temperature
U5
500 sheet cassette lift motor
U6
Main board problem
U7
Document glass too hot (with document feeder)
U8
Problem with line voltage
U9
Auto developer setup problem
Sharp 2116, 2118
Код ошибки
Описание
CH
Sorter not installed or not turned on
CH blinking
DV unit not installed, not connected properly
EE-EL
During developer calibration, problem of some kind. Over toned
EE-EU
During developer calibration, problem of some kind. Under toned
F1-00
Communication error between main board and sorter
F1-02
Transport motor drive
F1-04
Bin sensor problem. Upper or lower limit sensor problem
F1-05
Sorter bin home sensor
F1-06
Sorter bin motor drive
F1-14
Take out sensor problem
F2-31
Image density sensor problem
F2-32
Drum mark sensor problem
F2-35
Grid voltage correction will not work on the patch voltage is outside the expected range
H2-00
Fuser thermistor open
H3-00
Fuser temperature too high
H4-00
Fuser temperature too low. Lamp, thermal switch, connections
L1
Scan forward problem
L3
Scan return problem
L4
Drive problem; main motor, gear, sensor, bind
L5
Lens problem
L8-01
Zero cross (board problem)
L8-03
Auto exposure sensor problem
P
Paper feed problem
PC
Card counter not installed
U2-01
Memory loss
U2-04
EEPROM error
U5-00
Communication problem between main board and ADF
U5-01
Registration sensor problem during adjustment, or adjustment value is not a valid number
U5-02
Exit sensor adjustment problem; invalid adjustment value
U5-11
Paper feed drive problem
U5-12
Transport motor drive
Sharp 2120, 2216
Код ошибки
Описание
CC
Original detection problem
CH
Sorter not installed, or not turned on
CH blinking
DV unit not installed, not connected properly, or not latched in place properly
F1
Sub code 00: Communication error between main board and sorter. Sub code 02: Sorter transport motor drive.
F2
Sub code 31: Image density sensor. Could be a problem with light level. Sub code 32: Drum mark sensor problem. Does not see mark on drum or sensor not working properly.
H2
Sub code 00: Fuser thermistor open.
H3
Sub code 00: Fuser temperature too high.
H4
Sub code 00: Fuser temperature too low. Lamp, thermal switch, connections.
L1
Scan forward problem. Motor, sensor, board
L3
Scan forward problem. Motor, sensor, board.
L4
Drive problem; main motor, gear, sensor, bind.
L5
Lens problem. Motor sensor board.
L8
Sub code 01: Zero cross.
P
Paper feed problem or no paper
PC
Card counter not installed
U2
Sub code 01: Memory loss.
U4
Sub code 00: Communication problem between copier and duplex unit.
U5
Sub code 00: Communication problem between main board and ADF.
Sharp 2214
Код ошибки
Описание
A1
Jam in document feeder
A2
Jam in document feeder
C1
Cassette misfeed
C2
Cassette feed, bypass unplugged
C3
Bypass misfeed
E1
Paper feed jam
E3
Exit jam
EE-EL
Developer overtoned during setup
EE-EU
Developer undertoned during setup
J0
Developer setup taking place
J1
Add toner
J3
Drum unit not installed properly or missing
J7
Drum unit due for replacing
J8
Wrong drum unit or power was turned on after J7 displayed
L6
Key counter or other optional counter accessory problem
U1
Drive problem
U2
Scan
U3
Lens
U4-01
Fuser thermistor
U4-02
High fuser temperature
U4-03
Low fuser temperature
U5
500 sheet cassette lift motor
U6
Main board problem
U7
Document glass too hot (with document feeder)
U8
Problem with line voltage
U9
Auto developer setup problem
Sharp 2216
Код ошибки
Описание
CC
Original not detected in DF
CH
Sorter problems
CH blinking
Dev unit is not properly installed
L1
Scanner position error
L3
Scanner position error
L4
Main motor drive overloaded
L5
Lens position error
L8-01
Main board malfunction
L8-03
Auto-exposure sensor malfunction
H2-00
Fusing unit temperature error
H3-00
Overheated fusing unit
H4-00
The fusing unit doesn't heat up
U2-01
Memory back-up battery dead
U2-04
EPROM error
U5-00
Communication with the ADF is lost
U5-02
Exit sensor error in ADF
U5-11
Paper feed drive overloaded in ADF
U5-16
Cooling fan overloaded in ADF
F1-00
Lost communication with the Sorter
F1-02
Main drive overloaded in Sorter
F1-04
Bin position error in sorter
F1-05
Bin position error in sorter
F1-06
Paper exit drive overloaded in sorter
F1-14
Paper presence sensor error in sorter
F1-16
Paper transport motor overloaded in sorter
F2-31
ID pattern reading error
F2-32
ID pattern reading error
F2-33
Grid voltage error
F2-35
Grid voltage error
F2-37
ID pattern reading error
EE-EU
Low toner density in the developer
EE-EL
High toner density in the developer
P
Add paper
PC
Key counter not installed
Sharp 2314
Код ошибки
Описание
CH
If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing, developer seal still installed, or toner density sensor/main board problem.
EE
Sub code EU: undertoned. May be toner density sensor problem or developer unit problem. Sub code EL: Over toned. May be toner density sensor problem or developer unit problem.
H2
Sub code 0: Fuser thermistor.
H3
Sub code 0: Fuser temperature too high.
H4
Sub code 0: Fuser temperature too low.
L1
Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L3
Scan return problem. Sub code 0. Approximately same causes as L1
L4
Sub code 1: Main drive problem. Sensor, gear, motor.
L5
Sub code 2: Lens drive, motor, sensor.
L8
Sub code 1: Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE sensor problem.
PC
Key counter not installed.
SPFJAM
Document feeder problem.
U2
Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem.
U5
Sub code 5: high temperature at exposure glass when using document feeder.
Sharp 2414, 2514
Код ошибки
Описание
CH
If lit steadily, paper feed section cover is open or manual feed unit not installed properly. If flashing, developer seal still installed, or toner density sensor/main board problem.
EE
Sub code EU: undertoned. May be toner density sensor problem or developer unit problem. Sub code EL: Over toned. May be toner density sensor problem or developer unit problem.
H2
Sub code 0: Fuser thermistor.
H3
Sub code 0: Fuser temperature too high.
H4
Sub code 0: Fuser temperature too low.
L1
Scan problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L3
Scan return problem. Sub code 0. Approximately same causes as L1
L4
Sub code 1: Main drive problem. Sensor, gear, motor.
L5
Sub code 2: Lens drive, motor, sensor.
L8
Sub code 1 Power frequency varies by more than 5 % or for more than 5 sec. Sub code 3: AE sensor problem.
PC
Key counter not installed.
SPFJAM
Document feeder problem.
U2
Sub code 1: Main board EEPROM problem. Sub code 4: Memory problem.
U5
Sub code 5: high temperature at exposure glass when using document feeder
Sharp 7100, 7200
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
possible DV unit not installed properly
CH
Interlock or thermal fuse
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 7320, 7370
Код ошибки
Описание
CH
Door open or developer unit out
EL
Developer problem
EU
Developer set up problem
P flashing
Out of paper
P lit
No cassette in machine
PC
Personal counter not installed
U3
Auto exposure sensor problem
Sharp 750
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
Interlock or thermal fuse
CH
possible DV unit not installed properly
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
SERVICE TIPS & PROCEDURES. Maintenance Counter reset is CROP 20, Print General reset for error codes is CROP 14, Print
Sharp 755, 756, 760
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
possible DV unit not installed properly
CH
Interlock or thermal fuse
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 770
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
possible DV unit not installed properly
CH
Interlock or thermal fuse
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
0
Main board, operations panel
0
Data transfer (main and operations)
0
Data transfer (main and ADF)
1
Document feeded motors
1
Exposure lamp board or operations
2
Automatic exposure sensor, exposure lamp board
U
Press {Print} and read secondary code:
U3
Press {Print} and read secondary code:
U4
Press {Print} and read secondary code:
Sharp 7700, 7750
Код ошибки
Описание
0
Data transfer (main and ADF)
0
Data transfer (main and operations)
0
Main board, operations panel
1
Document feeded motors
1
Exposure lamp board or operations
2
Automatic exposure sensor, exposure lamp board
U
Press {Print} and read secondary code:
U3
Press {Print} and read secondary code:
U4
Press {Print} and read secondary code:
Sharp 771
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
possible DV unit not installed properly
CH
Interlock or thermal fuse
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 780
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
Interlock or thermal fuse
CH
possible DV unit not installed properly
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
CC
Document sensor
CH
Door open
EE
Developer did not set up properly
EL
Developer sensor
EU
Developer sensor
H2
Thermistor
H3
High temperature
H4
Low temperature
L1
Forward scan
L2
Forward scan
L3
Scan return
L5
Lens
L6
Bottom rotating cassette
L8
Signal
L9
Sorter
U1
Battery
U2
Back up battery
U3
Auto exposure sensor
U5
Problem in interface between machine and ADF
Sharp 7800
Код ошибки
Описание
CC
Document sensor
CH
Door open
EE
Developer did not set up properly
EL
Developer sensor
EU
Developer sensor
H2
Thermistor
H3
High temperature
H4
Low temperature
L1
Forward scan
L2
Forward scan
L3
Scan return
L5
Lens
L6
Bottom rotating cassette
L8
Signal
L9
Sorter
U1
Battery
U2
Back up battery
U3
Auto exposure sensor
U5
Problem in interface between machine and ADF
Sharp 781
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
possible DV unit not installed properly
CH
Interlock or thermal fuse
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
L6
Charge block switch
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 7850
Код ошибки
Описание
CC
Document sensor
CH
Door open
EE
Developer did not set up properly
EL
Developer sensor
EU
Developer sensor
H2
Thermistor
H3
High temperature
H4
Low temperature
L1
Forward scan
L2
Forward scan
L3
Scan return
L5
Lens
L6
Bottom rotating cassette
L8
Signal
L9
Sorter
U1
Battery
U2
Back up battery
U3
Auto exposure sensor
U5
Problem in interface between machine and ADF
Sharp 7900
Код ошибки
Описание
CC
Not sensing document on glass
CH
Door open/DV unit not installed properly
EE
DV did not set up properly
EL
DV problem-overtoned condition
EU
DV problem-undertoned condition
H2
Fuser thermistor
H3
Fuser temperature too high
H4
Fuser temperature too low
L1
Forward scan
L3
Return scan
L7
Developer unit shift problem
PC
Key counter
U1
Dead battery
U2
Battery problem
Sharp 810
Код ошибки
Описание
1
Open interlock switch
2
Bad thermofuse/thermistor
3
High or low temperature
4
Scanner problem
0
Data transfer
10
Mirror base
4
Stepping motor clock pulse
40
Lens
8
Mirror motor
U3
Press {Print} and read secondary code:
Sharp 8100
Код ошибки
Описание
0
Data transfer
10
Mirror base
4
Stepping motor clock pulse
40
Lens
8
Mirror motor
U3
Press {Print} and read secondary code:
Sharp 811
Код ошибки
Описание
1
Door or separator interlock
2
Instantly=Thermofuse
3
High temperature
4
Low temperature (if it takes 11 min)
5
Scanner problem if it takes several seconds
6
Optics problem on 820
7
Thermistor
Sharp 815
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
possible DV unit not installed properly
CH
Interlock or thermal fuse
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
L6
Charge block switch
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 816
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
Interlock or thermal fuse
CH
possible DV unit not installed properly
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
L6
Charge block switch
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 820
Код ошибки
Описание
1
Door or separator interlock
2
Instantly=Thermofuse
3
High temperature
4
Low temperature (if it takes 11 min)
5
Scanner problem if it takes several seconds
6
Optics problem on 820
7
Thermistor
A1
Document feeder problem.
CH
Toner cartridge not installed or not installed properly.
H2
Sub code 0: Fuser thermistor.
H3
Sub code 0: Fuser temperature too high.
H4
Sub code 0: Fuser temperature too low.
L1
Document feeder problem.
L3
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4
Sub code 1: Main drive problem. Sensor gear motor.
L5
Sub code 2: Lens drive, motor, sensor
P
Paper feed.
U2
Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5
Sub code 5: high temperature at exposing glass when using document feeder.
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
Interlock or thermal fuse
CH
possible DV unit not installed properly
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
L6
Charge block switch
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 8200
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
Interlock or thermal fuse
CH
possible DV unit not installed properly
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
L6
Charge block switch
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 825
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
A1
Document feeder problem.
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
possible DV unit not installed properly
CH
Interlock or thermal fuse
CH
Toner cartridge not installed or not installed properly.
H1
Heater thermal fuse
H2
Sub code 0: Fuser thermistor.
H2
Thermistor
H3
High Temperature
H3
Sub code 0: Fuser temperature too high.
H4
Sub code 0: Fuser temperature too low.
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Document feeder problem.
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L3
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4
PT/main motor
L4
Sub code 1: Main drive problem. Sensor gear motor.
L5
Lens
L5
Sub code 2: Lens drive, motor, sensor
L6
Charge block switch
P
Paper feed.
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U2
Sub code 1: Main board EEPROM problem. 4: Memory problem.
U3
Dark box
U5
Sub code 5: high temperature at exposing glass when using document feeder.
Sharp 826
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
Interlock or thermal fuse
CH
possible DV unit not installed properly
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
L6
Charge block switch
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 8260
Код ошибки
Описание
0
Data transfer
10
Mirror base
4
Stepping motor clock pulse
40
Lens
8
Mirror motor
U3
Press {Print} and read secondary code:
Sharp 830, 835
Код ошибки
Описание
A1
Document feeder problem.
CH
Toner cartridge not installed or not installed properly.
H2
Sub code 0: Fuser thermistor.
H3
Sub code 0: Fuser temperature too high.
H4
Sub code 0: Fuser temperature too low.
L1
Document feeder problem.
L3
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4
Sub code 1: Main drive problem. Sensor gear motor.
L5
Sub code 2: Lens drive, motor, sensor
P
Paper feed.
U2
Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5
Sub code 5: high temperature at exposing glass when using document feeder.
CC
Not sensing document on glass
CH
Door open/DV unit not installed properly
EE
DV did not set up properly
EL
DV problem-overtoned condition
EU
DV problem-undertoned condition
H2
Fuser thermistor
H3
Fuser temperature too high
H4
Fuser temperature too low
L1
Forward scan
L3
Return scan
L7
Developer unit shift problem
PC
Key counter
U1
Dead battery
U2
Battery problem
Sharp 8300, 8350, 8400
Код ошибки
Описание
CC
Not sensing document on glass
CH
Door open/DV unit not installed properly
EE
DV did not set up properly
EL
DV problem-overtoned condition
EU
DV problem-undertoned condition
H2
Fuser thermistor
H3
Fuser temperature too high
H4
Fuser temperature too low
L1
Forward scan
L3
Return scan
L7
Developer unit shift problem
PC
Key counter
U1
Dead battery
U2
Battery problem
Sharp 845
Код ошибки
Описание
A1
Document feeder problem.
CH
Toner cartridge not installed or not installed properly.
H2
Sub code 0: Fuser thermistor.
H3
Sub code 0: Fuser temperature too high.
H4
Sub code 0: Fuser temperature too low.
L1
Document feeder problem.
L3
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4
Sub code 1: Main drive problem. Sensor gear motor.
L5
Sub code 2: Lens drive, motor, sensor
P
Paper feed.
U2
Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5
Sub code 5: high temperature at exposing glass when using document feeder.
Sharp 850
Код ошибки
Описание
1
Door or separator interlock
2
Instantly=Thermofuse
3
High temperature
4
Low temperature (if it takes 11 min)
5
Scanner problem if it takes several seconds
6
Optics problem on 820
7
Thermistor
Sharp 8600
Код ошибки
Описание
0
Data transfer
10
Mirror base
4
Stepping motor clock pulse
40
Lens
8
Mirror motor
U3
Press {Print} and read secondary code:
Sharp 8875
Код ошибки
Описание
C2
Transfer corona problem
CH
If lit steadily, open door or other interlock. If flashing, developer unit not installed or not connected properly
Sorter index. If 0 is flashing, sorter index home sensor did not actuate. If 1 is flashing, sorter bottom actuator remained actuated
U1
Battery. Replace battery (might have 2) and do simulation 13 to reset
U2
Communication problem within boards. To reset, jumper test points W2 & U2
Sharp 900, 901
Код ошибки
Описание
0
Stepping motor
10
Mirror motor
40
Dark box switch
8
Mirror motor
C1
Charge corona
C2
Transfer corona
C3
Discharge corona
CH
possible DV unit not installed properly
CH
Interlock or thermal fuse
H1
Heater thermal fuse
H2
Thermistor
H3
High Temperature
H4
Low Temperature
H5
Lower thermofuse
H6
Lower thermistor
H7
High temperature in lower roller
H8
Low temperature in lower roller
L1
Forward Scan
L2
End of Scan
L3
Return of Scan
L4
PT/main motor
L5
Lens
L6
Charge block switch
P1
Copy lamp thermal fuse
U1
Low battery
U2
Data transfer
U3
Dark box
Sharp 9300, 9500, 9550
Код ошибки
Описание
0
Desk board and main board
0
Data transfer
10
Desk alignment board
10
Mirror base
20
Sort gate
4
Stepping motor clock pulse
40
Lens
8
Mirror motor
U3
Press {Print} and read secondary code:
U4
Press {Print} and read secondary code:
Sharp 9700, 9750
Код ошибки
Описание
40
Flashing - Lens home problem
C2
Transfer corona
CH
Lit - Door open
CH
Flashing - DV unit not installed
CL
Drum cleaner connector
H2
Thermistor
H3
High fuser temperature
H4
Low fuser temperature
L1
Mirror
L2
Scan
L3
Scan return
L4
Drive
L5
Lens
PC
Key counter
U1
Dead battery
U2
Dead battery
U3
Lens or mirror
U4
Duplex
Sharp Z50, 55, 70
Код ошибки
Описание
(Z70)E
Magnification dial not set properly
H
Heater problem (fuser has resettable
L
Scan problem
P
Paper feed problem
Sharp Z60
Код ошибки
Описание
F
Thermal fuse - exposure or fuser
H
Heater problem
L
Scan problem
U
Low Battery
Sharp Z800
Код ошибки
Описание
A1
Jam in document feeder
A2
Jam in document feeder
C1
Cassette misfeed
C2
Cassette feed, bypass unplugged
C3
Bypass misfeed
E1
Paper feed jam
E3
Exit jam
EE-EL
Developer overtoned during setup
EE-EU
Developer undertoned during setup
J0
Developer setup taking place
J1
Add toner
J3
Drum unit not installed properly or missing
J7
Drum unit due for replacing
J8
Wrong drum unit or power was turned on after J7 displayed
L6
Key counter or other optional counter accessory problem
U1
Drive problem
U2
Scan
U3
Lens
U4-01
Fuser thermistor
U4-02
High fuser temperature
U4-03
Low fuser temperature
U5
500 sheet cassette lift motor
U6
Main board problem
U7
Document glass too hot (with document feeder)
U8
Problem with line voltage
U9
Auto developer setup problem
Sharp Z810
Код ошибки
Описание
A1
Document feeder problem.
CH
Toner cartridge not installed or not installed properly.
H2
Sub code 0: Fuser thermistor.
H3
Sub code 0: Fuser temperature too high.
H4
Sub code 0: Fuser temperature too low.
L1
Document feeder problem.
L3
Scan return problem. Sub code is 0, but there is no more detail. Could be no scan drive; scan did not leave home; scan did not return home; scan overloaded; mirror motor problem; scan cable came off.
L4
Sub code 1: Main drive problem. Sensor gear motor.
L5
Sub code 2: Lens drive, motor, sensor
P
Paper feed.
U2
Sub code 1: Main board EEPROM problem. 4: Memory problem.
U5
Sub code 5: high temperature at exposing glass when using document feeder.
Если Вы не смогли найти своей модели в этом разделе, то есть вероятность, что Ваш аппарат является аналогом одного из представленных здесь. Проверить это можно в разделе "Совместимость".
Коды ошибок аналоговых копиров ("ксероксов") Sharp