Для отображения меню разрешите выполнение Java-скриптов в Вашем браузере На 1-ю страницу
Если Ваш копировальный аппарат Xerox выдал на индикации некий код, то узнать причину возникновения ошибки Вы можете в этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарата; а о том, как устранить сам сбой, есть много материалов в разделах "Ремонт ", "Ликбез ", "FAQ "; также Вы можете воспользоваться поиском или указателем материалов сайта
Xerox 1012, 1012(RE)
Код ошибки Описание E1 Jam between paper feed and fuser E3 Jam in fuser E5 Clam shell open E6 Paper feed section cover is open J1 Toner cartridge near empty J3 Drum cartridge not seated properly J7 Waste toner full (replace drum cartridge) L6 Key counter out L8 Exposure area overheat U1 No clock pulse (drive problem) U2 Scan problem U3 Lens/mirror problem (RE model only) U4 Heat problem U8 Exposure lamp control circuit problem E1 Jam between paper feed and fuser E3 Jam in fuser E5 Clam shell open E6 Paper feed section cover is open J1 Toner cartridge near empty J3 Drum cartridge not seated properly J7 Waste toner full (replace drum cartridge) L6 Key counter out L8 Exposure area overheat U1 No clock pulse (drive problem) U2 Scan problem U3 Lens/mirror problem (RE model only) U4 Heat problem U8 Exposure lamp control circuit problem
Xerox 1020
Код ошибки Описание LL Probable bad heater lamp
Xerox 1025
Код ошибки Описание A1 DF jam C1 PF jam cass. 1 C2 PF jam cass. 2 C3 PF jam cass. 3 C9 Bypass jam E1-1 Paper jam before exit switch E1-2 Paper jam E1-5 Paper jam E1-6 Paper jam E3-3 Paper jam at exit switch E3-4 Paper jam at exit switch E5 Front door open F1 Collator jam F5 Collator interlock F8 No power to collator F9 Collator bin home switch J7 250 copies since toner waste was full L5 Original cass. not present after clearing interrupt L6 Key counter L8 Platen glass too hot U1 Main motor clock pulse U2 Scan problem U3-1 Lens problem U4-1 Open thermistor U4-2 Low temperature U4-4 Temperature U4-5 Main PWB U6-1 Main PWB U6-2 Main PWB U6-3 Main board battery U6-4 Initialization U8 Exposure lamp
Xerox 1035
Код ошибки Описание A9 Scanner location C1 Paper feed - upper cassette C2 Paper feed - lower cassette C9 Bypass jam E5 Clam shell is open L6 Key counter U1 Off/On U2 Optics U4 Low fuser temperature
Xerox 1038
Код ошибки Описание A1 DF jam C1 PF jam cass. 1 C2 PF jam cass. 2 C3 PF jam cass. 3 C9 Bypass jam E1-1 Paper jam before exit switch E1-2 Paper jam E1-5 Paper jam E1-6 Paper jam E3-3 Paper jam at exit switch E3-4 Paper jam at exit switch E5 Front door open F1 Collator jam F5 Collator interlock F8 No power to collator F9 Collator bin home switch J7 250 copies since toner waste was full L5 Original cass. not present after clearing interrupt L6 Key counter L8 Platen glass too hot U1 Main motor clock pulse U2 Scan problem U3-1 Lens problem U4-1 Open thermistor U4-2 Low temperature U4-4 Temperature U4-5 Main PWB U6-1 Main PWB U6-2 Main PWB U6-3 Main board battery U6-4 Initialization U8 Exposure lamp
Xerox 2830
Код ошибки Описание A9 Scanner location C1 Paper feed - upper cassette C2 Paper feed - lower cassette C9 Bypass jam E5 Clam shell is open E5 Clam shell open L6 Key counter U1 Off/On U2 Optics U4 Low fuser temperature
Xerox 5011, 5012, 5014
Код ошибки Описание C8 Bypass jam/no paper C9 Bypass jam E1 Jam E3 Fuser jam E5 Clamshell open E6 PF section cover open J1 Toner cartridge amost empty J3 Copy cart (drum unit) missing/not seated right J7 Copy cartridge has run 18,000 copies J8 Copy cartridge. Improperly seated or possible only one of two fuses in the cartridge blew L6 Key counter L8 Exposure glass too hot U1 Drive problem U2 Scan problem U3 Lens or mirror drive problem U4 Fuser problem. Heat lamp, thermoswitch, SSR, thermistor U6 Battery on main board U8 Exposure lamp or exposure lamp circuit
Xerox 5016, 5017, 5316, 5317
Code Description A1-1 Document feeder feed jam A1-2 Document feeder belt jam A2-1 Document feeder exit jam A2-2 Duplex jam A3 DAD interlock A5 Duplex and DAD right side interlock A6 Copier jams after A9 Document feed belt drive motor C1-3 Top cassette misfeed C2-3 Middle cassette misfeed C3-3 Bottom cassette misfeed C9-3 Bypass misfeed E1-11 to E1-14 Paper jam in machine. Did not reach exit switch soon enough E1-6 Paper path jam E3-31 to E3-34 Exit switch jam E3-6 Fuser jam E5 Front door interlock E6 Right side interlock or TTM interlock F1 Sorter jam F5 Sorter interlock F8 Sorter board to copier main board communication problem F9 Sorter bins
Xerox 5018, 5028
Code Description A1 Document is ADF A1-8 Main board received reset signal A2 ADF jams A6, A7 ADF jams A9 ADF jams C1 - C4 Feed jam C5-1 to C5-4 Jams in various areas C5-2 Jams in various areas C5-3 Jams in various areas C5-4 Duplex jam E0 Machine has reset E1 Jam E1-E0 Registration jam E1-E5 Clamshell interlock E1-E6 Right side interlock E1-E7 Two tray interlock E1-E8 Sorter interlock E1-E9 Copy cartridge interlock E2 Reset signal happened E3 Jam E4 Exit jam E4-10 Exit jam E4-5 Clamshell interlock E4-6 Right side interlock E4-7 Two tray interlock. Duplex interlock E4-8 Sorter interlock E4-9 Copy cartridge interlock E5 Clamshell interlock E6 Right side interlock E7 Duplex interlock E9 Copy cartridge interlock F3-1 Sorter bin home switch F3-2 Sorter cam switch F3-3 Sorter cam switch J1-1 Add toner J1-2 Temporary low toner signal J2-0 Replace copy cartridge L2 2000 copies left on copy cartridge L3 ADF to machine communication problem L4 (flashing) 1000 copies left on fuser web rr Bad EPROM on main board U0 Main board U2 Scan problem U2-1 Scan home U3-00 Cam drive problem U3-01 Cam movement slow U3-04 Main board to duplex communication U3-09 Cam problem U3-12 Jogger problem U3-19 Cam problem U3-21 Cam problem U3-23 Cam problem U3-29 Cam problem U3-32 Cam problem U3-34 Cam problem U3-39 Cam problem U3-43 Cam problem U3-45 Cam problem U3-49 Cam problem U3-54 Cam problem U3-56 Cam problem U3-59 Cam problem U4-1 Fuser problem. Long warm up U4-2 Low fuser temperature after warm up U4-3 High fuser temperature U4-4 Open fuser thermistor U4-6 Replace fuser web U4-7 Thermistor signal problem U7-1 Copy cartridge belt drive problem U9-3 Exposure lamp problem U9-4 Toner motor U9-5 Problem in warm up
Xerox 5312, 5313, 5314
Код ошибки Описание C1 Upper paper feed problem. Did not reach feed sensor C2 Lower paper feed problem. Did not reach feed sensor E1 Exit jam. Paper did not reach exit sensor E3 Exit jam. Paper still on exit sensor J1 Add toner J3 Copy cartridge (drum unit) not installed J7 Copy cartridge (drum unit) must be replaced J8 Copy cartridge (drum unit) problem L6 Problem with an accessory. Installed but not initialized U1 Drive problem. Main motor, gear etc. U2 Scan problem U3 Main board dip switches wrong. Lens drive problem U4 Fuser problem. Heat lamp, thermal switch, overheat, thermistor. U6 EPROM error U8 Auto exposure sensor. No exposure lamp or weak lamp
Xerox 5318, 5320, 5322
Code Description A1-11 Original ready switch A1-12 Feed sensor A1-1 to A1-32 All indicate a paper path problem, etc. in the ADF A1-21 Original ready switch and document registration sensor or both the document feed sensor and document registration sensor A1-22 ADF registration sensor A1-23 Original did not reach ADF registration sensor quickly enough A1-24 ADF sensor stuck down too long A1-25 ADF sensor actuated at the wrong time during single sheet feed A1-26 ADF sensor not actuated quickly enough in sheet feed mode A1-31 In reverse, ADF sensor is not actuated soon enough A1-32 In reverse, ADF sensor is actuated too long A2 ADF exit problems A2-1 Original ready sensor and ADF exit switch are actuated or ADF feed in sensor and ADF exit switch are both actuated A2-2 ADF exit switch A2-3 ADF exit switch is not actuated on time A3 Irregular size documents A3-1 Wrong size original sensed in 1:1 mode A3-2 Wrong size original sensed in the 2:1 mode A5 ADF interlock A5 ADF interlock A6 ADF single sheet document reset. A6-1 Reset original A6-2 Reset sheet feeder A7 Document cover interlock A8 ADF exit interlock C1 Tray 1 jam C1-2 Paper feed problem in tray 1 C1-3 Paper does not reach registration C2 Tray 2 jam C3 Tray 3 jam C3-1 Paper feed problem from tray 3 C3-2 Paper feed problem from tray 3 C3-3 Paper feed problem from tray 1 C6-1 Duplex paper feed problem C6-2 Duplex and/or tray 1 paper feed problem C6-3 Paper feed problem from tray 1 C7-1 Paper feed problem from HCF C7-2 Paper feed problem from HCF on tray 1 C7-3 Paper feed problem from tray 1 C8 Paper stays in tray or duplex or HCF C8-1 Paper on tray 1 feed sensor C8-2 Paper on tray 2 feed sensor C8-3 Paper on tray 3 feed sensor C8-4 Paper on HCF feed sensor C8-5 Paper in duplex section C9 Bypass feed problem C9-3 Paper from bypass did not reach registration sensor quickly enough E1-10 to E1-25 Internal jam E1-6 Paper on registration sensor E2 Reset signal happened. Might read E-2 something else. E3-30 to E4-14 Exit jam E3-30 to E3-35 Exit switch actuated too long E3-6 Exit jam E3-6 Paper on exit switch E4-10 to E4-14 Inverter sensor not actuated. E4-10 to E4-45 Paper did not reach inverter switch soon enough E4-15 Inverter sensor E4-40 to E4-45 Duplex entry sensor E4-6 Paper on inverter switch E4-6 Inverter sensor E5 Front door interlock E6-1 Tray 1 interlock E6-2 2 tray or duplex interlock E6-3 HCF interlock E7-2 Duplex inverter interlock E7-3 Duplex interlock E8-10 to E8-15 Paper on duplex feed sensor is not actuated soon enough E8-6 Paper in duplex E8-6 to E8-15 Duplex entry sensor F1-1 Paper did not reach sorter F1-2 Paper stayed on sorter feed sensor F1-6 Sorter exit sensor F3 Paper size not available for sort/stack F5 Sorter interlock H2-1 Communication problem between main board and duplex board H2-2 Side guard sensor problem H3-1 Communication problem between main board and HCF H3-2 Upper limit sensor problem on HCF H6-1 ADF size sensor H6-2 ADF nudgeer sensor H6-3 Belt drive motor does not have 24 volts. Black toner is empty, but 100 copies have been run without changing toner J1 Black toner is empty, but 100 copies have been run without changing toner J3 Replace copy cartridge J3 No copy cartridge (drum unit) J7 Copy cartrige must be replaced J8-1 Wrong copy cartridge installed J8-2 Copy cartridge EEPROM must be changed L6 Auditron or other counter problem L6 Key counter not installed L8 Platen glass temperature is too high L9 Communication problem between interimage erase/edge lamps and main board U1-1 Main motor drive problem U2-1 Scan home problem U2-1 to U2-4 Scan home sensor U2-2 Scan home problem or optics problem U2-3, U2-4 Scan home problem U3-1 Lens sensor problem U4-1 Fuser thermistor open U4-2 Fuser did not warm up properly U4-3 Fuser temperature too high U4-4 Fuser problem. Staying on too long U4-6 High fuser temperature U5-1 Sorter bin home switch not activated U5-2 Sorter bin home switch stayed actuated U5-3 Sorter bin home switch U5-4 Sorter bin home switch U6-1 ROM problem U6-2 RAM problem U6-3 Low battery U6-4 Incorrect value in NVM. Reinitialize main board with code 20-96 U8-1 Exposure lamp problem U8-2 Communication problem main board and exposure board U8-3 Exposure lamp or exposure lamp board problem U8-4 to U8-6 Problem with exposure lamp, lamp sensor, lamp board
Xerox 5328
Code Description A1 Document in ADF A1-8 Main board received reset signal A2 ADF jams A6 ADF registration jam A7 ADF interlock A9 Tray 1 jam C1 Tray 2 jam C2 Tray 3 jam C3 Bypass feed jams C4 Machine has reset E1 Jam E1-5 Clamshell interlock E1-6 Right side interlock E1-7 Two tray interlock, or duplex interlock E1-8 Sorter interlock E1-9 Copy cartridge interlock E1 or E1-0 Registration jam E2 Reset signal happened E3 Jam in transfer area E4 Exit jam E4-0 Exit jam E4-5 Clamshell interlock E4-6 Right side interlock E4-7 Two tray interlock E4-8 Sorter interlock E4-9 Copy cartridge interlock E5 Clamshell interlock E6 Right side interlock E9 Copy cartridge interlock F3-1 Sorter bin home switch F3-2 Sorter cam switch F3-3 Sorter cam switch F5 Sorter interlock J1-1 Add toner J1-2 Temporary low toner signal J2-1, J2-2 Replace copy cartridge J5, J6 ADF to machine communications problem L2 2000 copies left on cartridge L3 ADF to machine communications problem L4 (flashing) 1000 copier left on fuser web L6 Auditron or other counter problem LL Main board. Try simulation 1.1 to initialize rc Wrong operation panel installed rr Bad EPROM on main board. Try 1.1 U0 Main board U2 Scan problem U2-1 Scan home U2-2 Scan home or scan encoder U2-4 Scan home or scan dual page sensor U2-7 Scan home U4-1 Fuser problem. Long warm up U4-2 Low fuser temperature after warm up U4-3 High fuser temperature U4-4 Open fuser thermistor U4-6 Replace fuser web. U4-7 Thermistor signal problem U7-1 Copy cartridge belt drive problem U9-3 Exposure lamp problem U9-4 Toner motor U9-5 Problem in warm-up
Xerox 5330
Code Description A1-1 to A1-32 All indicate a paper path problem, etc. in the ADF. A2 ADF exit problems A3 Irregular size documents A5 ADF interlock A6 ADF single sheet document reset. A7 Platen interlock A8 ADF exit interlock C1 Tray 1 jam C2 Tray 2 jam C3 Tray 3 jam C6-1, C6-2 Jams related to duplex C6-3 Registration sensor, re tray 1 C7-1, C7-2 HCF feed problems C7-3 Tray 1 feed problem C8 Paper stays in tray or duplex or HCF C9 Bypass feed problem E1-10 to E1-25 Internal jam E1-6 Paper on registration sensor E2 Reset signal happened. Might read E-2 something else. E3-30 to E4-14 Exit jam E3-6 Exit jam E4-10 to E4-14 Inverter sensor not actuated. E4-15 Inverter sensor E4-40 to E4-45 Duplex entry sensor E4-6 Inverter sensor E5 Front door interlock E6-1 Tray 1 interlock E6-2 2 tray or duplex interlock E6-3 HCF interlock E7-2, E7-3 Duplex interlock E8-6 to E8-15 Duplex entry sensor F1-1 Sorter entry sensor F1-6 Sorter exit sensor F3 Paper size not available for sort/stack F5 Sorter interlock J1 Add toner J3 Replace copy cartridge J7 Replace copy cartridge J8-1 Wrong copy cartridge installed J8-2 Copy cartridge EEPROM L6 Auditron or other counter problem L8 Platen glass temperature is too high L9 Communication problem between interimage erase/edge lamps and main board U1-1 Main motor drive problem U2-1 to U2-4 Scan home sensor U3-1 Lens sensor U4-1 Open fuser thermistor U4-2 Fuser did not warm up properly U4-3 Fuser temperature too high U4-4 Fuser problem. Staying on too long U4-6 High fuser temperature U5-1 Sorter bin home switch not activated U5-2 Sorter bin home switch stayed actuated U5-3 Sorter bin home switch U5-4 Sorter bin home switch U6-1 ROM problem U6-2 RAM problem U6-3 Low battery U6-4 Incorrect value in NVM. Reinitialize main board with code 20-96 U8-1 to U8-6 Problem with exposure lamp, lamp sensor, lamp board
Xerox 5340, 5343
Code Description 00-009; 030 to 033 A door was opened while paper was being fed 00-047 Paper in duplex 00-1 Auditron 00-2 Diagnostic error 00-3 Faults error 00-4 Ric error 00-5 Job manager system error 00-6 LLM interface 00-7 Standby error 00-8 Communications error 00-9 Xerographic error 01-300 Front interlock 01-310 Right upper interlock 01-315 Left upper interlock 01-320 Left lower interlock 01-325 Fuser interlock 02-910 Key counter missing 02-920 Wrong combination of accessories 03-321, 322, 326, 327 LLM to ISIL communications problems 03-328 IOT communications problem with duplex or tray 4 03-330 IOT communications problems with HCF 03-335, 03-336 LLM communications problems with edit 03-340 NVM memory 03-341, 03-347 Communications problems between IOT and sorter 03-350, 03-354 Communications problem with LLM and user interface 03-363, 03-364 Communications problem between LLM & optics 03-370, 03-373 Communications problem between LLM & DADF 03-380, 384 03-416, 03-422 RAM memory problem 03-424, 426 NVM memory problem 03-430, 432 Billing problem 03-439 GRAIB communications problem 03-440 RIC communications problem 03-441 RIC NVM problem 03-442 Modem 03-443, 03-458 RIC problems 03-460 Serial communications processor problem 04-300 Main motor or drive problem 05-100, 05-108 DADF registration sensor 05-110 DADF exit sensor 05-115, 120 DADF jams 05-305 DADF document drive 05-310, 312 DADF document sensor 05-316 DADF registration sensor jam 05-325 DADF exit sensor 05-335, 341, 345 DADF interlock switches 06-300, 06-310 Scan problems 06-315 Scan drive 06-320A, 320B, 320C, 325 Scan problem 06-330 Lens drive 06-340 Exposure control problem 06-342 LLM CPU problem 06-344, 06-350 Exposure cvontrol problem 06-352 IOT CPU problem 07-300, 315, 330, 345 Tray faults 07-360, 07-370 HCF problems 07-375, 380A, 380B Duplex problems 08-100, 08-110 Feed problems. Lead edge of copy paper is late getting to feed sensor of tray 1 08-115, 08-162 Feed problem. Lead edge of copy paper is late getting to registration sensor 08-165 Paper jam at registration sensor 08-310, 08-370 Paper at a sensor when power is turned on 08-330 DADF nudger sensor 08-380 Registration side to side problem with home position 08-390 Nip 09-300 Copy cartridge finished (drum unit) 09-310 Add black toner Add color toner 09-320 Add color toner 09-330 Wrong copy cartridge (wrong drum unit) 09-340 Drum cartridge not installed properly 09-350 Waste toner full 100 A fault has occurred 10-100 Exit jam 10-105 Exit jam 10-110 Vertical sensor jam 10-120, 122, 125 Duplex jam 10-150, 155 Too much or not enough paper in duplex tray 10-300 Fuser thermistor 10-302 Low fuser temperature 10-304 Bad fuser temp 10-308 High fuser temperature or open thermistor 10-310 High fuser temperature 10-312 Fuser not up to temperature after energy save 10-314 Fuser problem 10-320 Fuser web finished 10-330, 335, 340 Exit switch, vertical sensor switch actuated when power is turned on 11-100, 11-116 Sorter jam 11-150, 11-176 Sorter auto stapler jam 11-310, 314, 316 Sorter interlock 11-325A, B, C, D, E, F, G Sorter index 11-352, 354, 356 Sorter auto stapler interlocks 11-365A, B, C, D, E Sorter auto stapler bin 11-370, 371, 372A, 373A, 373B, 374 Sorter auto stapler staple failure, staple home problem or tamper home problem 11-385A, 385B, 390A,B,C,D,E, 396A Sorter auto stapler staple failure, staple home problem or tamper home problem 301 Fuser web must be replaced 302 Copy cartridge (drum unit) must be replaced 501 Tray 1 must be rebuilt 502 Tray 2 must be rebuilt 503 Tray 3 must be rebuilt 504 Tray 4 must be rebuilt 505 HCF must be rebuilt 506 Bypass must be rebuilt 507 Duplex unit must be rebuilt 508 Replace black developer 509 Replace red developer 510 Replace green developer 512 Replace brown developer 513 Copy cartridge (drum unit) will need replacing soon 514 Fuser web will need replacing soon 515 DADF belt should be replaced 516 DADF feed rollers should be replaced 517 Replace exposure lamp 518 Replace suction filter 519 Replace ozone filter 520 Replace optics filter 521 Replace particle filter 522 Replace upper fuser roller 523 Replace fuser pawls 524 Replace pressure roller 525 Replace pressure roller pawls 900-905 Key operator calls
Xerox 5345
Код ошибки Описание 01-01 Frequency monitoring and zero cross problem 01-02 Interlock 01-03 AC power problem 01-04 Finisher interlock 01-05 24v problem 03-01 Optics to main board communication problem 03-02 Software reset problem 03-03 Could be punched holes in the lead edge of the original 03-04 Software problem 03-06 Low battery 03-07 NVM not initialized or is missing or defective 03-17 Communication problem between main board and finisher board 03-18 Initializes one NVM counter to agree to others 03-19 All three NVM counter to agree with others 03-20 Main board/interface board problems 03-21 Problem with RIC NVM 03-22 RIC modem problem 03-23 RIC real time clock failure. 03-25 RIC NVM problem or not initialized 03-27 NVM problem 03-28 Watchdog software problem 03-29 Microprocessor crystal not at correct frequency 03-30 No software response from finisher after 20 seconds have elapsed 06-01 Lens did not reach 1.1 position 06-02 1/2 rate scanner problem 06-03 Scan home problem 06-04 Scan home problem 06-05 Scan home problem 06-06 Scan encoder 06-07 Scan encoder 06-08 Scan drive boost 06-09 Scan encoder 06-11 Scan encoder pulse phases 06-12 Insufficient scan damping 07-01 Duplex tray not home during duplexing 07-02 Tray 2 not home when selected 07-13 Tray 2 height sensor problem 07-15 Tray 2 empty 07-16 Tray 1 door open 07-18 Tray 1 stack sensor 07-22 Tray 1 empty 07-26 Tray 1 bypass switch actuated too long 07-27 Tray 1 bypass switch deactuated too early 07-30 Paper in duplex 07-31 Paper in duplex 07-32 Duplex tray empty, when paper should be there 08-10 Paper did not reach tray 2 input tray sensor 08-11 Paper did not reach duplex input sensor 08-12 Paper did not reach tray 1 08-14 Paper did not leave tray 2 input sensor quickly enough 08-18 Trail edge did not reach tray 2 input sensor quickly enough 08-19 Trail edge did not reach tray 1 input sensor quickly enough 08-20 Paper in duplex 08-21 Paper in tray 2 input 08-22 Paper in tray 2 or duplex at wrong time 08-23 Paper at tray 1 input at wrong time 08-24 Paper in tray 1 at wrong time 08-28 Upper and lower nips problem 09-08 Low toner condition 09-12 Drum signals are out of range 09-13 Unstable drum patch readings 09-15 Patch is too dark 09-16 Patch is too light 09-17 Open toner container access cover 09-18 Low toner level 09-21 Low toner sensor disconnected 09-22 Low toner condition, even after machine has been theoretically, adding toner 10-02 Low fuser temperature 10-03 High fuser temperature 10-06 Paper did not reach out put switch 10-07 Paper stayed on output switch 10-10 Paper did not reach decurler sensor 10-11 Paper did not reach decurler sensor 10-12 Paper on decurler sensor 10-13 Paper did not reach duplex entry sensor in time 10-14 Paper did not reach duplex entry sensor in time 10-15 Paper on entry sensor at wrong time 10-17 Fuser temperature is too high and fuser relay has deactuated 12-01 Paper at finisher input sensor 12-02 Paper did not reach finisher 12-03 Paper reached finisher too soon 12-05 Paper at stapler 12-06 Paper at stapler 12-07 Paper did not reach stapler 12-08 Paper did not reach stapler 12-10 Complied motor not working properly 12-15 Eject motor problem and/or eject encoder 12-20 Stacker motor problem 12-21 Stacker interlock 12-22 Stacker bottom sensor 12-23 Stacker bottom sensor 12-24 Stacker bottom sensor senses full 12-25 Stack height sensor 12-26 Stack height sensor 12-27 Stack height sensor 12-30 Offset home sensor 12-31 Offset home sensor 12-32 OCT switch 12-35 Eject nip carriage 12-36 Eject cam interlock 12-37 Eject nip carriage open timing 12-38 Eject cam interlock 12-40 Tamper motor 12-41 Tamper home problem 12-42 Tamper home sensor 12-43 Staple load sensor 12-44 Tamper home sensor 12-45 Tamper home sensor 12-50 Low on staples 12-51 Stapler home sensor 12-52 Stapler home sensor 12-53 Eject cam interlock 33-37 Too few documents 55-01 RDH interlock switch open during use 55-04 Paper on bypass sensor 55-05 Paper at vacuum timing sensor 55-06 Paper on output sensor 55-10 No paper reached S31 55-20 Paper did not leave S31 at correct time 55-24 Set counter arm problem 55-25 Documents in input tray not detected 55-27 Lead edge did not reach S35 at correct time 55-2955-30 Trail edge did not reach S35 at correct time 55-31 S32, ADF registration sensor did not see paper at correct time 55-32 S32 did not see trail edge at correct time 55-33 S36 One too many documents 55-36 One too many documents 55-39 Hole count problem on document feeder belt 55-40 Document belt travel problem 55-41 Document belt mistracking or skewing 55-45 Paper at inverter sensor 55-47 Inverter sensor did not see paper lead edge at correct time 55-49 More than 50 sheets in input tray 55-50 Right side interlock 55-51 Left side interlock 55-55 Document on glass 93-93 NVM has to be initialized after new software installed
Xerox 5350, 5352
Code Description 00-009, 030, 031, 032, 033 A door was opened while paper was being fed 00-047 Paper in duplex 00-1 Auditron 00-2 Diagnostic error 00-3 Faults error 00-4 Ric error 00-5 Job manager system error 00-6 LLM interface 00-7 Standby error 00-8 Communications error 00-9 Xerographic error 01-300 Front interlock 01-310 Right upper interlock 01-315 Left upper interlock 01-320 Left lower interlock 01-325 Fuser interlock 02-910 Key counter missing 02-920 Wrong combination of accessories 03-321, 322, 326, 327 LLM to ISIL communications problems 03-328 IOT communications problem with duplex or tray 4 03-330 IOT communications problems with HCF 03-335, 336 LLM communications problems with edit 03-340 NVM memory 03-341-347 Communications problems between IOT and sorter 03-350-354 Communications problem with LLM and user interface 03-363, 364 Communications problem between LLM & optics 03-370-03-373 Communications problem between LLM & DADF 03-380, 384 03-416-422 RAM memory problem 03-424, 426 NVM memory problem 03-430, 432 Billing problem 03-439 GRAIB communications problem 03-440 RIC communications problem 03-441 RIC NVM problem 03-442 Modem 03-443-458 RIC problems 03-460 Serial communications processor problem 04-300 Main motor or drive problem 05-100-108 DADF registration sensor 05-110 DADF exit sensor 05-115, 120 DADF jams 05-305 DADF document drive 05-310, 312 DADF document sensor 05-316 DADF registration sensor jam 05-325 DADF exit sensor 05-335, 341, 345 DADF interlock switches 06-300-310 Scan problems 06-315 Scan drive 06-320A, 320B, 320C, 325 Scan problem 06-330 Lens drive 06-340 Exposure control problem 06-342 LLM CPU problem 06-344-350 Exposure cvontrol problem 06-352 IOT CPU problem 07-300, 315, 330, 345 Tray faults 07-360-370 HCF problems 07-375, 380A, 380B Duplex problems 08-100-110 Feed problems. Lead edge of copy paper is late getting to feed sensor of tray 1 08-115-162 Feed problem. Lead edge of copy paper is late getting to registration sensor 08-165 Paper jam at registration sensor 08-310-370 Paper at a sensor when power is turned on 08-330 DADF nudger sensor 08-380 Registration side to side problem with home position 08-390 Nip 09-300 Copy cartridge finished (drum unit) 09-310 Add black toner Add color toner 09-320 Add color toner 09-330 Wrong copy cartridge (wrong drum unit) 09-340 Drum cartridge not installed properly 09-350 Waste toner full 100 A fault has occurred 10-100 Exit jam 10-105 Exit jam 10-110 Vertical sensor jam 10-120, 122, 125 Duplex jam 10-150, 155 Too much or not enough paper in duplex tray 10-300 Fuser thermistor 10-302 Low fuser temperature 10-304 Bad fuser temp 10-308 High fuser temperature or open thermistor 10-310 High fuser temperature 10-312 Fuser not up to temperature after energy save 10-314 Fuser problem 10-320 Fuser web finished 10-330, 335, 340 Exit switch, vertical sensor switch actuated when power is turned on 11-100-116 Sorter jam 11-150-176 Sorter auto stapler jam 11-310, 314, 316 Sorter interlock 11-325A,B,C,D,E,F,G Sorter index 11-352, 354, 356 Sorter auto stapler interlocks 11-365A,B,C,D,E Sorter auto stapler bin 11-370,371,372A,373A,373B,374 Sorter auto stapler staple failure, staple home problem or tamper home problem 11-385A,385B,390A,B,C,D,E,396A Sorter auto stapler staple failure, staple home problem or tamper home problem 301 Fuser web must be replaced 302 Copy cartridge (drum unit) must be replaced 501 Tray 1 must be rebuilt 502 Tray 2 must be rebuilt 503 Tray 3 must be rebuilt 504 Tray 4 must be rebuilt 505 HCF must be rebuilt 506 Bypass must be rebuilt 507 Duplex unit must be rebuilt 508 Replace black developer 509 Replace red developer 510 Replace green developer 512 Replace brown developer 513 Copy cartridge (drum unit) will need replacing soon 514 Fuser web will need replacing soon 515 DADF belt should be replaced 516 DADF feed rollers should be replaced 517 Replace exposure lamp 518 Replace suction filter 519 Replace ozone filter 520 Replace optics filter 521 Replace particle filter 522 Replace upper fuser roller 523 Replace fuser pawls 524 Replace pressure roller 525 Replace pressure roller pawls 900-905 Key operator calls
Xerox 5355
Код ошибки Описание 01-01 Frequency monitoring and zero cross problem 01-02 Interlock 01-03 AC power problem 01-04 Finisher interlock 01-05 24v problem 03-01 Optics to main board communication problem 03-02 Software reset problem 03-03 Could be punched holes in the lead edge of the original 03-04 Software problem 03-06 Low battery 03-07 NVM not initialized or is missing or defective 03-17 Communication problem between main board and finisher board 03-18 Initializes one NVM counter to agree to others 03-19 All three NVM counter to agree with others 03-20 Main board/interface board problems 03-21 Problem with RIC NVM 03-22 RIC modem problem 03-23 RIC real time clock failure. 03-25 RIC NVM problem or not initialized 03-27 NVM problem 03-28 Watchdog software problem 03-29 Microprocessor crystal not at correct frequency 03-30 No software response from finisher after 20 seconds have elapsed 06-01 Lens did not reach 1.1 position 06-02 1/2 rate scanner problem 06-03 Scan home problem 06-04 Scan home problem 06-05 Scan home problem 06-06 Scan encoder 06-07 Scan encoder 06-08 Scan drive boost 06-09 Scan encoder 06-11 Scan encoder pulse phases 06-12 Insufficient scan damping 07-01 Duplex tray not home during duplexing 07-02 Tray 2 not home when selected 07-13 Tray 2 height sensor problem 07-15 Tray 2 empty 07-16 Tray 1 door open 07-18 Tray 1 stack sensor 07-22 Tray 1 empty 07-26 Tray 1 bypass switch actuated too long 07-27 Tray 1 bypass switch deactuated too early 07-30 Paper in duplex 07-31 Paper in duplex 07-32 Duplex tray empty, when paper should be there 08-10 Paper did not reach tray 2 input tray sensor 08-11 Paper did not reach duplex input sensor 08-12 Paper did not reach tray 1 08-14 Paper did not leave tray 2 input sensor quickly enough 08-18 Trail edge did not reach tray 2 input sensor quickly enough 08-19 Trail edge did not reach tray 1 input sensor quickly enough 08-20 Paper in duplex 08-21 Paper in tray 2 input 08-22 Paper in tray 2 or duplex at wrong time 08-23 Paper at tray 1 input at wrong time 08-24 Paper in tray 1 at wrong time 08-28 Upper and lower nips problem 09-08 Low toner condition 09-12 Drum signals are out of range 09-13 Unstable drum patch readings 09-15 Patch is too dark 09-16 Patch is too light 09-17 Open toner container access cover 09-18 Low toner level 09-21 Low toner sensor disconnected 09-22 Low toner condition, even after machine has been theoretically, adding toner 10-02 Low fuser temperature 10-03 High fuser temperature 10-06 Paper did not reach out put switch 10-07 Paper stayed on output switch 10-10 Paper did not reach decurler sensor 10-11 Paper did not reach decurler sensor 10-12 Paper on decurler sensor 10-13 Paper did not reach duplex entry sensor in time 10-14 Paper did not reach duplex entry sensor in time 10-15 Paper on entry sensor at wrong time 10-17 Fuser temperature is too high and fuser relay has deactuated 12-01 Paper at finisher input sensor 12-02 Paper did not reach finisher 12-03 Paper reached finisher too soon 12-05 Paper at stapler 12-06 Paper at stapler 12-07 Paper did not reach stapler 12-08 Paper did not reach stapler 12-10 Complied motor not working properly 12-15 Eject motor problem and/or eject encoder 12-20 Stacker motor problem 12-21 Stacker interlock 12-22 Stacker bottom sensor 12-23 Stacker bottom sensor 12-24 Stacker bottom sensor senses full 12-25 Stack height sensor 12-26 Stack height sensor 12-27 Stack height sensor 12-30 Offset home sensor 12-31 Offset home sensor 12-32 OCT switch 12-35 Eject nip carriage 12-36 Eject cam interlock 12-37 Eject nip carriage open timing 12-38 Eject cam interlock 12-40 Tamper motor 12-41 Tamper home problem 12-42 Tamper home sensor 12-43 Staple load sensor 12-44 Tamper home sensor 12-45 Tamper home sensor 12-50 Low on staples 12-51 Stapler home sensor 12-52 Stapler home sensor 12-53 Eject cam interlock 33-37 Too few documents 55-01 rdh interlock switch open during use 55-04 Paper on bypass sensor 55-05 Paper at vacuum timing sensor 55-06 Paper on output sensor 55-10 No paper reached S31 55-20 Paper did not leave S31 at correct time 55-24 Set counter arm problem 55-25 Documents in input tray not detected 55-27 Lead edge did not reach S35 at correct time 55-2955-30 Trail edge did not reach S35 at correct time 55-31 S32, ADF registration sensor did not see paper at correct time 55-32 S32 did not see trail edge at correct time 55-33 S36 One too many documents 55-36 One too many documents 55-39 Hole count problem on document feeder belt 55-40 Document belt travel problem 55-41 Document belt mistracking or skewing 55-45 Paper at inverter sensor 55-47 Inverter sensor did not see paper lead edge at correct time 55-49 More than 50 sheets in input tray 55-50 Right side interlock 55-51 Left side interlock 55-55 Document on glass 93-93 NVM has to be initialized after new software installed
Xerox XC520, 540, 560, 580
Код ошибки Описание H2 Fuser thermistor H3 Fuser temperature too high. Must be reset in diagnostics H4 Fuser temperature too low. Must be reset in diagnostics L3 Scan problem L4 Min motor drive problem L8 Exposure lamp not lightning or not enough light reaching auto exposure sensor P Paper did not feed
Xerox 5622
Code Description A1-1 to A1-32 All indicate a paper path problem, etc. in the ADF A2 ADF exit problems A3 Irregular size documents A5 ADF interlock A6 ADF single sheet document reset A7 Platen interlock A8 ADF exit interlock C1 Tray 1 jam C2 Tray 2 jam C3 Tray 3 jam C6-1, C6-2 Jams related to duplex C6-3 Registration sensor, re tray 1 C7-1, C7-2 HCF feed problems C7-3 Tray 1 feed problem C8 Paper stays in tray or duplex or HCF C9 Bypass feed problem E1-10 to E1-25 Internal jam E1-6 Paper on registration sensor E2 Reset signal happened. Might read E-2 something else E3-30 to E4-14 Exit jam E3-6 Exit jam E4-10 to E4-14 Inverter sensor not actuated E4-15 Inverter sensor E4-40 to E4-45 Duplex entry sensor E4-6 Inverter sensor E5 Front door interlock E6-1 Tray 1 interlock E6-2 2 tray or duplex interlock E6-3 HCF interlock E7-2, E7-3 Duplex interlock E8-6 to E8-15 Duplex entry sensor F1-1 Sorter entry sensor F1-6 Sorter exit sensor F3 Paper size not available for sort/stack F5 Sorter interlock J1 Add toner J3 Replace copy cartridge J7 Replace copy cartridge J8-1 Wrong copy cartridge installed J8-2 Copy cartridge EEPROM L6 Auditron or other counter problem L8 Platen glass temperature is too high L9 Communication problem between interimage erase/edge lamps and main board U1-1 Main motor drive problem U2-1 to U2-4 Scan home sensor U3-1 Lens sensor U4-1 Open fuser thermistor U4-2 Fuser did not warm up properly U4-3 Fuser temperature too high U4-4 Fuser problem. Staying on too long U4-6 High fuser temperature U5-1 Sorter bin home switch not activated U5-2 Sorter bin home switch stayed actuated U5-3, U5-4 Sorter bin home switch U6-1 ROM problem U6-2 RAM problem U6-3 Low battery U6-4 Incorrect value in NVM. Reinitialize main board with code 20-96 U8-1 to U8-6 Problem with exposure lamp, lamp sensor, lamp board
Инженерные машины Xerox 2510/2515/2520
Если Вы не смогли найти своей модели в этом разделе, то есть вероятность, что Ваш аппарат является аналогом одного из представленных здесь. Проверить это можно в разделе "Совместимость ".
Последнее обновление - январь 2006 г.
вверх
Коды ошибок копиров ("ксероксов") Xerox